522213
13
Zoom out
Zoom in
Previous page
1/28
Next page
3. ADJUSTMENTS
5
3.2 Setting Up NMEA Ports
Ports J4 and J5 output data in NMEA 0183 format. Select the data to output from those ports,
along with baud rate and output interval. The default settings are as shown in the table below.
Default settings for ports 2 and 3
1. Grasp the cover at its right and left sides, pull the cover outward slightly and then lift the cover
to remove it.
2. Open the inner cover and turn on the power.
On the circuit board, find the heading indication, several LEDs, and four operating buttons.
The Heading LED is lit.
3. Push the [Menu/Cancel] button several times to light the Sentence LED on the Port 2 line.
4. Push the [Enter] button. The Sentence LED starts flashing and the sentence currently select-
ed to output from port 2 is shown with a numeric. See the illustration below for numeric and
data sentence.
5. Push the [+] or [-] button to display the numeric corresponding to the data sentence you wish
to output.
6. Push the [Enter] button. The sentence LED stops flashing.
Port no. Sentence Baud rate (bps) Tx interval (ms)
J4 (Port 2) HDT (Heading) 4800 100
J5 (Port 3) ATT (Heading, pitch, roll)
HVE (Heave)
38400 25
OUTPUT PROCESSING
0 3
Heading Pitch
Sentence
Roll
Bps
Output
Interval
BpsSentence
Offset
Output
Interval
Operating
buttons
Use the [Menu/Cancel]
button to show the
heading indication.
Push the [Enter] button
to show the heading
offset value.
- +
Enter
Menu/
Cancel
Port 2
Port 3
When offset
is minus
OUTPUT PROCESSING
0003
Offset
Heading Pitch
Sentence
Roll
Bps
Output
Interval
BpsSentence
Output
Interval
Sentence
LED
Current sentence setting
(example: 1: HDT (Heading, true))
Other indications:
2: HDG (Heading, Variation, Deviation)
3: HDM (Heading, Magnetic)
4: ATT (Heading, pitch, roll) and HVE (Heave)
5: VTG (Course over ground and ground speed)
GGA (Global positioning system(GPS fix data)
ZDA (Date and time)
6: RMC (Recommended minimum specific
GPS/TRANSIT data)
ZDA (Date and time)
7: Sentences of 4 and 5.
8: Sentences of 6 and 1.
- +
Enter
Menu/
Cancel
Port 2
Port 3
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno IF-NMEASC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno IF-NMEASC in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info