13377
53
Zoom out
Zoom in
Previous page
1/85
Next page
10-3
RANGE/SPEED UNIT
Selects the unit for range and speed; nm/kt
(default setting), km/ km/h, sm/ sm/h.
DEPTH UNIT
Selects unit of depth measurement among,
feet, fathoms, and meters. The default set-
ting is feet.
TEMP UNIT
Selects unit of water temperature measure-
ment between Celsius or Fahrenheit. The de-
fault setting is Fahrenheit.
LAT/LON DISPLAY
Displays the seconds of latitude and longi-
tude positions in hundredths, thousandths
(default setting) or ten thousandths.
TIME DISPLAY
Selects time display format for 12 hour or
24 hour (default setting).
WAYPOINT SW
Provides automatic or manual waypoint
switching when following a route. For further
details, see page 7-4. The default setting is
AUTO2.
COURSE VECTOR
You may extend a line from the own ship po-
sition to show ship’s course. The line can be
a vector (the length depends on the ship’s
speed.) or a line (course bar). The default set-
ting is LINE.
BEARING
A navigation device outputs both true and
magnetic bearings. A magnetic bearing is true
bearing plus (or minus) earth’s magnetic de-
viation. Thus the equation for finding mag-
netic bearing is;
true bearing ± x (magnetic variation)° = mag-
netic bearing
You can display your ship’s course and bear-
ing to waypoint in true or magnetic bearing,
and the default setting is magnetic.
MAG VARIATION
The magnetic variations for all areas of the
earth are preprogrammed into this unit. The
preprogrammed variation is accurate for most
instances, however you may wish to manu-
ally enter a variation.
1. Select MAG VARIATION, and press the
soft key EDIT to show the mag variation
window.
MAG VARIATION
AUTO
'
MANUAL 0.7
°
W
Figure 10-5 Mag variation window
2. Select MANUAL.
3. Key in magnetic deviation value.
4. Press the soft key W<-->E to switch be-
tween East and West and vice versa, if
necessary.
5. Press the soft key ENTER or the [ENTER]
key to finish.
TD DISPLAY
Position may be shown in Loran C TDs (de-
fault setting), Decca TDs, or latitude and lon-
gitude. To display position in TDs select Loran
C or Decca here and choose TD at POSI-
TION DISPLAY below. You can select the
Loran C or Decca chain to use on the TD
SETUP menu. For details see TD SETUP
menu on page 10-6.
POSITION DISPLAY
Displays position in latitude and longitude
(default setting) or Loran C or Decca TDs.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno GP1850D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno GP1850D in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info