716650
45
Zoom out
Zoom in
Previous page
1/67
Next page
Great user manuals database on UserManuals.info
9-1
9.1 Installation of Display Unit
Mounting considerations
The display unit can be installed on a table-
top, on the overhead, or in a panel (optional
flush mounting kit required). Refer to the
outline drawing on page D-2, D-3 or D-4
for installation instructions. When selecting
a mounting location, keep in mind the fol-
lowing points:
Locate the unit away from exhaust pipes
and vents.
The mounting location should be well
ventilated.
Mount the unit where shock and vibra-
tion are minimal.
Locate the display unit away from equip-
ment which generates electromagnetic
fields such as a motor or generator.
Allow sufficient maintenance space at the
sides and rear of the unit and leave suffi-
cient slack in cables, to facilitate mainte-
nance and servicing.
Tabletop and overhead mounting
Tabletop
Overhead
Figure 9-1 Tabletop and overhead
mounting methods
Flush mounting
There are two types of flush mounting kits.
For details, see the outline drawing on page
D-3 and D-4.
9. INSTALLATION
9.2 Installation of Antenna Unit
Mounting considerations
Install the antenna unit referring to the in-
stallation diagram on page D-1. When se-
lecting a mounting location for the antenna
unit, keep in mind the following points:
Select a location out of the radar beam.
The radar beam will obstruct or prevent
reception of the GPS satellite signal.
The location should be well away from a
VHF antenna. A GPS receiver is inter-
fered by a harmonic wave of a VHF an-
tenna.
There should be no interfering object
within the line-of-sight to the satellites.
Objects within line-of-sight to a satellite,
for example, a mast, may block reception
or prolong acquisition time.
Mount the antenna unit as high as pos-
sible. Mounting the antenna unit as high
as possible keeps it free of interfering
objects and water spray, which can inter-
rupt reception of GPS satellite signal if
the water freezes.
The length of the whip antenna for the
GP-35 should be no longer than 1.2 meter
to prevent antenna damage. Do not use a
2.5 meter whip antenna.
Do not shorten the antenna cable.
If the antenna cable is to be passed
through a hole which is not large enough
to pass the connector, you may unfasten
the connector with a needle nose pliers
and 3/8-inch open-end wrench. Refasten
it as shown in Figure 9-2 after running
the cable through the hole.
Center pin (soldered)
Clamp nut
Connector shell
Gasket (reddish brown)
Washer
Shield
Figure 9-2 How to assemble the connector
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno GP-30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno GP-30 in the language / languages: English as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info