716650
33
Zoom out
Zoom in
Previous page
1/67
Next page
Great user manuals database on UserManuals.info
7-2
8. Select AUTO or MANU. AUTO uses
ship’s average speed to calculate time-
to-go; MANU is for manual entry of
speed.
9. Press the [ENT] key. If you selected
AUTO no further operation is necessary.
For MANU, press the [ENT] key again.
Enter speed with the Cursor Pad and
press the [ENT] key.
Figure 7-5 shows what the display might
look like using Route-01 for an example.
CALCULATION
MODE: ROUTE
NO. : 01 (WYPTS: 4)
KOBEOSAKA
SPD : AUTO
TTG: 1H39M ETA: ---
RNG: 9.06 nm BRG: --- °
Time-to-Go
Estimated Time of Arrival
Range Bearing
Figure 7-5 Typical calculation
display (route)
7.2 DGPS Setup
The GP-35 is equipped with a DGPS bea-
con receiver, and the GP-30 may be con-
nected to a DGPS beacon receiver. Set up to
receive the DGPS beacon signal as follows:
1. Press the [MENU] key twice.
2. Select D-GPS and press the [ENT] key.
D-GPS SETUP
BEACON : EXT
STATION : MANUAL
RATE : 200 BPS
FREQ : 310.0 kHz
BEACON STATION : GOOD
D-GPS DATA : GOOD
SIG. S : 00.0 dB SNR: 00.0 dB
Figure 7-6 D-GPS SETUP menu
3. Press the [ENT] key.
4. Select INT for internal DGPS beacon re-
ceiver; EXT for external DGPS beacon
receiver. Press the [ENT] key.
5. The cursor is on the STATION line. Press
the [ENT] key.
6. Choose DGPS beacon station selection
method: AUTO 1, AUTO 2 or
MANUAL.
AUTO 1, AUTO 2: Automatically
search for nearest DGPS beacon station.
The GP-35 always searches for nearest
DPGS beacon station.
MANUAL: Manually enter DGPS bea-
con station specifications (on the RATE
and FREQ lines), referring to the DGPS
reference station list in the Appendix.
7. If you selected AUTO, no further opera-
tion is necessary; you may press the
[MENU] key twice to finish. For
MANUAL, the cursor is now on the
RATE line. Press the [ENT] key.
8. Select the transmission rate of the DGPS
beacon station nearest you, among 50,
100 or 200 bps. Press the [ENT] key.
9. The cursor is now on the FREQ line.
Press the [ENT] key.
10.Enter nearest DGPS beacon station’s fre-
quency with the Cursor Pad.
11.Press the [ENT] key.
12.Press the [MENU] key twice to finish.
7.3 Bearing Reference
Ship's course and bearing to a waypoint may
be displayed in true or magnetic bearing.
Magnetic bearing is true bearing plus (or mi-
nus) earth’s magnetic deviation.
The default setting displays magnetic bear-
ings.
1. Press the [MENU] key twice.
2. Select PLOTTER.
3. Press the [ENT] key.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno GP-30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno GP-30 in the language / languages: English as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info