522205

Furuno FI-502 CH WIND ANGLE Manual

44
Zoom out
Zoom in
Previous page
1/62
Next page
5. INSTALLATION
34
5.4.2 Setting up FI-506
Rudder calibration
You can apply an offset to the rudder indication to remove any deviation
from actual and displayed rudder angles.
1. With the rudder centered, press the
W and X keys together until the
instrument starts beeping continuously. The beeping indicates you
have correctly enabled the calibration mode.
2. Use the
W and X keys to move the pointer to the zero position.
3. Press the
W and X keys together again to save the setting and
escape from the calibration mode.
Terminal resistor on/off
The terminal resistor enables/disables connection of the FI-506 to an
NMEA 2000 network, and it is disabled at the factory. To turn the resistor
on or off, press and hold down the BRILL and
W keys together until you
hear a beep. Then, press the
X key to turn the resistor on or off. The
number of beeps indicates ON or OFF. Two beeps for ON, three beeps
for OFF. Press the BRILL and
W keys together to save the setting and
return to normal operation. A beep sounds upon completion.
Synchronization on/off
The data shared within the FI-50 instruments series can be synchro-
nized, so that all data agrees. You can turn synchronization of all data on
or off, or synchronize data by group, A and/or B. For group synchroniza-
tion, instruments having like group synchronization settings are synchro-
nized.
To set synchronization, press and hold down the BRILL and
X keys to-
gether until you hear a beep. Then, press the
X key to select applicable
synchronization setting. The number of beeps and beep duration indi-
cate the setting as shown below. Press the BRILL and X keys together
to save the setting and return to normal operation. A beep sounds upon
completion.
ON: Beep
*1
→OFF
*1
→Beep
*1
A: Beep*
1
→OFF*
1
→Beep
*3
B: Beep
*3
→OFF
*1
→Beep
*1
→OFF
*1
→Beep
*1
→OFF
*1
→Beep
*1
OFF: Beep
*3
→OFF
*2
→Beep
*3
→OFF
*2
→Beep
*3
*1
200 ms,
*2
500 ms,
*3
1000 ms
Factory defaults
Press the and BRILL keys together until you hear a beep, indicating
completion. Press the same keys again to return to normal operation.
… 44 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno FI-502 CH WIND ANGLE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno FI-502 CH WIND ANGLE in the language / languages: English as an attachment in your email.

The manual is 2,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info