28292
200
Zoom out
Zoom in
Previous page
1/223
Next page
8. MAINTENANCE, TROUBLESHOOTING
8-13
8.10 Clearing Memories
Your equipment has a memory for each of the plotter, radar and sounder sections. These
memories can be cleared to restart operation with default settings.
The following data are not cleared:
Radar: Heading adjustment, timing adjustment, MBS level, tuning point, tuning indication
(short, medium, long), video level, dead sector, antenna height, STC curve, antenna type,
on time, tx time, Sounder: White marker, hue, signal level, TLL output, depth calibration,
range.
1. Press the MENU key to open the menu.
2. Press the E: SYSTEM CONFIGURATION soft key.
3. Press the C: SYSTEM SETUP soft key.
4. Press the B: TEST & CLEAR soft key.
5. Press the D: MEMORY CLEAR soft key.
MEMORY
CLEAR
PROCESSORUNIT NO
GPSSENSOR NO
NETWORKSOUNDER NO
RETURNE
EDITA
Memory clear menu
6. Use the Trackball to choose the memory to clear.
7. Press the A: EDIT soft key.
8. Use the Trackball to select YES, then press the C: ENTER soft key. One of the
following displays appears depending on the selection made at step 6.
ALL SETTNGS EXCEPT
SNDR ARE RESET TO
DEFAULT. ARE YOU SURE?
YES ... PUSH ENTER KNOB
NO ... PUSH CLEAR KEY
BEGIN COLD START
TO CLEAR GPS
MEMORY. ARE YOU SURE?
YES ... PUSH ENTER KNOB
NO ... PUSH CLEAR KEY
SOUNDER WILL BE
SET TO DEFAULT.
ARE YOU SURE?
YES ... PUSH ENTER KNOB
NO ... PUSH CLEAR KEY
Display Unit Clear GPS Receiver Clear Network Sounder Clear
Windows for clearing memory
9. Push the ENTER knob to clear the memory selected.
10. Press the MENU key to close the menu.
11. Turn the power off and on again.
Note: The message “SYSTEM HAS FAILED START UP TEST. PLEASE CONTACT A
LOCAL FURUNO REPRESENTATIVE FOR REPAIR. PUSH ANY KEY TO CONTINUE.”
may appear when powering on the display unit immediately after clearing any memory. It is
not an indication of malfunction. Press any key to continue operation.
200


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1944CBB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1944CBB in the language / languages: English as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info