28292
9
Zoom out
Zoom in
Previous page
1/223
Next page
viii
SYSTEM CONFIGURATIONS
All NavNet products incorporate a “network circuit board” to integrate each NavNet product
on board through an optional LAN cable (Ethernet 10BASE-T). Each NavNet product is
assigned an IP address to enable transfer of images between other NavNet products. For
example, video plotter pictures can be transferred to a radar and vice versa. Pictures
received via the NavNet may be adjusted at the receiving end.
The number of processor units which may be installed depends on the number of network
sounder connected. For a system incorporating three or more products, a “hub” is required
to process data.
For one network sounder: one radar and three plotters, or four plotters
For two network sounder: one radar and two plotters, or four plotters
Note: NavNet2 equipment cannot be connected to initial version NavNet equipment.
NavNet system (Model 1824C-BB/1834C-BB/1934C-BB/1944C-BB/1954C-BB)
Heading sensor
Navigator
Echo sounder
Rectifier
RU-3423
GPS receiver
GP-310B/320B
12 - 24 VDC*
Network
Sounder
ETR-6/10N
ETR-30N
Other NavNet
system
(GD-1920C-BB, etc.)
Antenna Unit
MODEL
1834C-BB
MODEL
1934C-BB
MODEL
1944C-BB
Processor unit
RPU-015
100/110/115/220/230 VAC
1φ, 50/60 Hz*
Monitor
(Local supply)
MODEL
1954C-BB
Control unit
RCU-017
Power Supply
Unit PSU-005
*: The power for the power supply unit
and display unit must be drawn from
the same power source.
Facsimile
Receiver
FAX-30
MODEL1824C-BB
PUSH TO ENTERPUSH TO ENTER
DEFDEF
MNOMNO
VWXVWX
_'#_'#
POWERPOWER
RANGERANGE
TXTX
00
JKLJKL
44
77
STUSTU
55
88
ABCABC
2211
BB
GAINGAIN
ALARMALARM
EBLEBL
VRMVRM
PQRPQR
YZ&YZ&
66
99
DISPDISP
EE
MENUMENU
CC
DD
CLEARCLEAR
GHIGHI
33
SAVESAVE
MOBMOB
HIDEHIDE
SHOWSHOW
AA
POWER
DATA 3
NETWORK
CONT DATA 1DATA 2
DJ-1
SLAVE DISPLAY
RGB OUT
NTSC/PAL
2
GND
3
INPUT
12-24 VDC
1
CARD SLOT
3
2
1
GND
F.G.
12 VDC
OUTPUT
OPTION
ARPA
ARP-11
: Standard
: Option
: Local supply
NavNet system (Model 1824C-BB/1834C-BB/1934C-BB/1944C-BB/1954C-BB)
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1944CBB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1944CBB in the language / languages: English as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info