28276
23
Zoom out
Zoom in
Previous page
1/46
Next page
3-4
3. Select 6. Int Reject.
4. Select level desired by operating the
omnipad.
5. Press the [ACQ/ENTER] key.
6. Press the [MENU] key to close the menu.
IR1, IR2 or IR3 appears at the bottom right
corner on the display when the interference
rejection circuit is turned on.
3.6 Selecting Pulsewidth
Pulsewidth is the time in microseconds nec-
essary to transmit a single radar pulse. The
longer the pulsewidth the greater the direc-
tion range capability, however range accu-
racy and range resolution are reduced.
Pulsewidth can be selected to short or long
on the 1.5 and 3 nautical mile ranges.
1. Press the [MENU] key.
2. Select OTHER MENU and press the
[ACQ/ENTER] key.
3. Select 7. Pulselength.
4. Select Short or Long by pressing the
omnipad.
5. Press the [ACQ/ENTER] key to select.
6. Press the [MENU] key to close the menu.
3.7 Guard Alarm
The guard alarm allows the operator to set
the desired range and bearing for a guard
zone. When ships, islands, landmasses, etc.
violate the guard zone an audible alarm
sounds and the offending target blinks to call
the operators attention.
The guard alarm is a useful anti-collision
aid, but does not relieve the operator of the
responsibility to also keep a visual lookout
for possible collision situations. The alarm
should never be used as the sole means
for detecting possible collision situations.
CAUTION
Selection of guard zone type
The guard alarm can be set to sound when a
target either enters or exits the guard zone.
You can select which type of guard alarm you
want through the menu.
In alarm
The alarm sounds on targets entering the
guard zone. G (IN) appears at the top right-
hand corner when the In alarm is selected.
Out alarm
The alarm sounds on targets exiting the guard
zone. G (OUT) appears at the top right-hand
corner when the Out alarm is selected.
IN ALARM
OUT ALARM
Guard
zone
Dashed line:
no alarm
Figure 3-7 In and Out alarms
Selecting guard zone type
1. Press the [MENU] key, select OTHERS
MENU, and then press the [ACQ/EN-
TER] key.
2. Select 17. Guard Mode and In (alarm
on target entering zone) or Out (alarm
on target exiting zone) by operating the
omnipad.
3. Press the [ACQ/ENTER] key.
4. Press the [MENU] key to close the menu.
Setting a guard zone
1. Mentally create the guard zone you want
to set. Figure 3-8 shows an example.
2. Operate the omnipad to set the cursor on
point A (or B). Press the [GUARD] key.
*G (IN) or *G (OUT), with asterisk blink-
ing, appears at the top right-hand corner
of the display. See Figure 3-8 (2). (The
asterisk indicates the guard zone is par-
tially set.)
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1932MK2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1932MK2 in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info