28276

Furuno 1932MK2 Manual

18
Zoom out
Zoom in
Previous page
1/46
Next page
2-7
VRM1
Offset EBL
(EBL1)
6.0 NM
2.0
EBL1 origin
(initial position
of target)
Target moved
here.
EBL1
bearing
70.0° R
VRM
6.0 NM
VRM1
range
EBL
Figure 2-9 Predicting collision course by
using the offset EBL
Measuring range and bearing
between two targets
The procedure which follows shows how to
measure the range and bearing between tar-
get “A” and target “B” in Figure 2-10.
1. Operate the omnipad to place EBL1’s ori-
gin (cursor) on the center of target “A.”
2. Press the [EBL/VRM SELECT] key to
choose the EBL1 readout and then press
the [EBL/VRM CONTROL] key.
3. Press the [MENU] key, select EBL OFF-
SET from the menu, and then press the
[ACQ/ENTER] key. EBL1’s origin shifts to
cursor location.
4. Press the [EBL/VRM CONTROL] key.
5. Operate the omnipad to bisect target “B”
with EBL1. Check the EBL1 readout to
find the bearing between target “A” and
target “B.”
6. Press the [EBL/VRM SELECT] key to
choose the VRM1 readout. Operate the
omnipad to place the outside edge of
VRM1 on the inside edge of target “B.”
Check the VRM1 readout to find the range
between target “A” and target “B.”
7. To cancel the offset EBL, select EBL OFF-
SET from the menu, and then press the
[ACQ/ENTER] key.
VRM1
EBL1
bearing
70.0° R
VRM
4.5 NM
VRM1
range
EBL1
A
B
Figure 2-10 Measuring the range and
bearing between two targets by using the
offset EBL
2.14 Offcentering the Picture
Your vessel’s position can be offcentered to
75% of the range in use to view the situation
around your vessel without changing the
range or size of targets.
1. Press the omnipad to set the cursor where
desired.
2. Press the [F1 (A/C SEA)] control if its func-
tion is set for SHIFT (default setting), or
select SHIFT from the menu.
OFFCENTER appears at the top right
corner of the display when the picture is
offcentered.
Cursor Cursor
2 Press [F1] to offcenter
display.
1 Pleace cursor
where desired.
Figure 2-11 Offcentering the picture
Cancelling offcentered picture
Press the [F1 (A/C SEA)] control (if function
is SHIFT).
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1932MK2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1932MK2 in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info