28270

Furuno 1932 Manual

51
Zoom out
Zoom in
Previous page
1/63
Next page
AP-5
LARGE CIRCLE
The plot symbol of a target under tracking
becomes twice as large as the normal symbol
when the target is selected for data reading.
Note 1:The target to be acquired should be
within 0.2 to 16 nm from own ship and not
obscured by sea or rain clutter for successful
acquisition.
Note 2:When you want to acquire 11th target,
cancel tracking one of less important targets.
Note 3:When auto acquisition mode (Auto
ACQ) is on, up to 5 targets can be acquired.
For detail, see next section titled Automatic
Acquisition.
WARNING
When a tracked target nears another
tracked target, the targets may be
"swapped." When two targets come close
to each other, one of the two can become
a "lost target." Should this happen,
reacquisition of the "lost target" is required
after the two targets have separated.
Automatic Acquisition
The Auto plotter ARP-10 can acquire up to 5
targets automatically by setting the Auto Ac-
quisition area predefined in the system. If Auto
ACQ is selected after more than 5 targets have
been manually acquired, only the remaining
capacity of targets can be automatically ac-
quired. Example; when 7 targets acquired
manually, then the Auto ACQ is switched on
only 3 targets can be acquire automatically.
When five targets have been automatically
acquired, "AUTO TARGET FULL" message
appears at top left corner on the display.
Setting Auto Acquisition Area
Auto acquisition area is predefined between
2.0 and 2.5 nm in range and 45º on either side
of the heading line in bearing. If a target come
into this area, it is acquired automatically.
Deactivating the Auto Plotter
To deactivate the Auto Plotter,
1. Open the "ARP-10 MENU".
2. Operate the omnipad to select the "1. Dis-
play".
5. Operate the omnipad to select "Off".
6. Press the [ACQ/ENTER] key.
7. Press the [MENU] key to close the menu.
Acquiring targets
Manual Acquisition
Follow the steps below to manually acquire a
target. Up to 10 targets can be manually ac-
quired.
1. Place the cursor (+) on a target of interest
by operating the omnipad.
2. Press the [ACQ/ENTER] key.
The plot symbol changes its shape according
to the status as below. A vector appears in
about one minute after acquisition indicating
the target's motion trend. If the target is con-
sistently detected for three minutes, the plot
symbol changes to a solid mark. If acquisi-
tion fails, the target symbol blinks and disap-
pears shortly.
SQUARE (dotted)
Immediately after acquisition - Plot symbol
shown in broken lines.
SQUARE (dotted with a vector)
One minute after acquisition - Vector still un-
reliable.
CIRCLE (Solid with a vector)
3 minutes after acquisition - Plot symbol
changes to a solid circle indicating the stable
tracking condition.
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1932 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1932 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno 1932

Furuno 1932 User Manual - Spanish - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info