28270
40
Zoom out
Zoom in
Previous page
1/63
Next page
29
Final preparation
1. Place the antenna housing cover on the
housing. Loosely fasten the four fixing
bolts on the cover.
Fixing
holes
Scanner housing
cover
Pinning
hole
Figure 6-15 Fastening the antenna
housing cover
2. Apply grease to the two slot pins. Using a
wooden hammer to prevent damage to
paint, insert slotted pins into the pinning
holes until the pin head is flush with the
scanner housing surface.
Radiator
bracket
Ship’s
bow
Slotted pin
Face in
stern direction.
Figure 6-16 How to insert slot pins
3. Now is the time to fix the radiator to the
radiator bracket. Apply anticorrosive seal-
ant (silicone sealant) to hatched areas, to
prevent corrosion. See the figure below.
Apply silicone sealant into threaded holes
on the scanner radiator. Remove the cap
on the radiator bracket and orient the ra-
diator bracket as shown in Figure 6-13.
Apply grease to the O-ring and set it to the
center of the radiator bracket. Coat the ra-
diator fixing bolts with silicone sealant.
Fasten the radiator to the radiator bracket
with the FURUNO logo on the radiator fac-
ing ship’s bow.
Waveguide
Groove
Note: Apply anticorrosive
sealant to hatched areas,
antenna radiator bottom
view of XN8 type radiator.
Figure 6-17 How to coat radiator with
silicone sealant for XN8 type radiator
Flat washer
Spring washer
Hex head bolt
(M8 x 30)
Radiator bracket
Coat bolts with
silicone sealant.
Scanner
radiator
O-ring
Apply silicone sealant
into threaded holes.
Note: Apply anticorrosive sealant
to hached areas, antenna bracket
for XN12A type radiator.
Figure 6-18 Fastening the radiator to the
radiator bracket
4. Open the antenna housing cover and fix the
stay as shown in Figure 6-19.
5. One end of the cable with 15-, 9- and 7-
way plugs has already been connected to
RTB-9100 inside the scanner housing.
Mate the 15- and 9-way plugs with jacks
J812 and J811 on the transceiver module,
respectively. Connect the 7-way plug to
jack J701 on the MP Board. Secure the
cable between RTB-9100 and J701 with the
cable tie as shown in Figure 6-19.
Cable
tie
J812
J811
Stay
MP Board
Fasten ground
wire here.
Figure 6-19 Antenna unit, cover opened
6. Fasten the ground wire (black) of the sig-
nal cable to the chassis as shown in Figure
6-19.
7. Loosely fasten the antenna housing cover.
You will tighten the fixing bolts after con-
firming magnetron heater voltage.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1932 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1932 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno 1932

Furuno 1932 User Manual - Spanish - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info