28260
43
Zoom out
Zoom in
Previous page
1/63
Next page
32
6.3 Exchange of Fuse for
24/32V Power Supply
The power cable comes with a 10A fuse in
the fuse holder. This fuse is for use with a
12V DC power supply. For 24V/32V DC
power supply, replace the fuse with the 5A
fuse (supplied) and attach 5A label (supplied)
to fuse holder.
6.4 Checking the Installation
After completing the installation, it is a good
idea to recheck it to be sure all steps were
correctly done. Use the table 6-1 to check the
installation.
Tick box
The signal cable is securely retained
against the mast or mounting platform and
is free of interference from running rigging.
The cable gland or entry on the deck, if
provided, is waterproofed.
The power connections to the battery are
of correct polarity.
The plugs at the rear of the display unit
are tightly fastened.
The fuse in the power cable is 10A (12V)
or 5A (24V/32V DC).
6.5 Adjustments
This section covers adjustment of the radar
after installation. You will need to
¡ adjust tune/video amplifier level input
¡ enter antenna height
¡ align heading
¡ adjust sweep timing
¡ adjust main bang suppression
¡ setting a blanking area, and
¡ confirm magnetron heater voltage.
These adjustments are done through the radar
install menus.
Preparation
1. Turn off the radar. While pressing and hold-
ing down the [GAIN] control (at least three
seconds), press the [POWER] key.
2. Press the [MENU] key, and select OTH-
ERS by using the omnipad, and pressing
[ACQ/ENTER] key.
3. Select 24. Installation setup.
4. Press the [ACQ/ENTER] key to open the
installation setup menu.
Figure 6-20 Connections on the display unit
CAUTION
Replace the fuses to
5 A for 24/32 VDC set.
CAUTION
Ground the equipment. Ungrounded
equipment can give off or receive
electro-magnetic interference or give
electrical shock.
Power cable connector
Ground terminal
External equipment
connector
Signal cable connector
(DJ-1, waterproof)
Left: HDG connector
Mid: NMEA connector (for NAV)
Right:NMEA connector (for E/S)
(To be used for Remote
Display, External Alarm
Buzzer, OP03-21 and
Radar Plotter, RP-110)
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Furuno 1832 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Furuno 1832 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Furuno 1832

Furuno 1832 User Manual - Spanish - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info