68173
41
Zoom out
Zoom in
Previous page
1/103
Next page
Error while receiving an SMS
There may be various reasons for it not being possible to receive an SMS, or for only having voice output:
·
The feature SMS has not been applied for (and approved) at your network service provider and/or
the provider of the SMS Service Center.
·
The SMS has been transferred by outside service providers which did not transmit this message
as an SMS.
·
Permanent number suppression (inhibit) is activated for your ISDN connection.
·
Ten SMS messages have already been stored in your telephone, preventing anyfurther SMS mes
-
sages from being received.
Silent signalling
If you do not wish calls to be signaled with the programmed ringer melody and volume, you can active the »Silent
signalling« feature. Depending on the specific setting, all calls will be displayed optically or along with a brief
acoustic signal. To set the volume for the brief acoustic signal, proceed as described on page37 or »R« in the display
shows that the function »Station guarding« is activated.
»No« The function »Station guarding« is deactivated.
»ok« Calls are signaled optically only (»Q« shown in the display).
»Ringing signal off« Calls are signaled first by a brief acoustic signal and then only optically (»q«).
Only for msn-1 The functions described above are configured only for MSN-1. This assumes that several
MSNs have been configured in the system telephone.
a
ss
Quiet No / Ringing signal 0ff/ ok
You have the option of logging the accrued communication costs for your telephone. You must apply for this feature
to your network service provider.
Ask your service provider on the possibilities of charge data transmission. Please note that transfer of all cost
information from the exchange office to your telephone may not always be possible for technical reasons. Any price
reductions and special rates or convenience features utilized may result in differences between the data stored in the
telephone and information listed in the phone bill.
Procedures for charge rate transmission
There are several standardized procedures for transmitting call charge rates. Usually the same procedure is
employed at one connection that is recognized and stored automatically for future use by the telephone.
In the event that the type of charge information transmission is not stored in the phone, »Wrong charge type« then
appears in the display.
In this case you should delete all charge information stored in the telephone (see also: viewing/deleting total costs).
Recognition and saving of the procedure that is used for transfer of cost information is then re-activated.
Information:
You can set the tariff factor and the currency while configuring your telephone with the PC.
Silent signalling Monitoring costs
37
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Funkwerk CS410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Funkwerk CS410 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info