503729

Funai WD6D-M101 Manual

75
Zoom out
Zoom in
Previous page
1/84
Next page
75
EN
Introduction Connections Playback Editing OthersFunction SetupRecording VCR Functions
Basic Setup /
TV View Operation
GENERAL
No image from HDMI connection. • Check the HDMI connection. (Check the status of the HDMI related indications.)
• Check whether the connected monitor device or other device supports HDCP.
(This unit will not output a video signal unless the other device supports HDCP.)
• Check the setting of HDMI.
• Check whether the output format of this unit (HDMI FORMAT) matches the
supported input format of other connected device.
• If the unit is connected to the unauthorised display device with an HDMI cable,
the audio and video signals may not be output when playing back a commercial
DVD-video.
CHANNEL
TV channels cannot be changed. • Check if the connections are made securely and correctly.
• Check if the cables are damaged.
• Try “Channel” setting by following the steps on pages 21-23.
Some settings are lost even though you
followed the procedure correctly.
• If you unplug the AC mains cable while the warning message, “Saving settings.
Please wait.”, is displayed, some settings may be lost. Do not unplug the AC
mains cable while the message is displayed (It will take about 1 minute.).
Only specific channels do not appear. • The channels may be set to be skipped. (See pages 22, 25.)
Though auto tuning was completed,
you cannot watch the DVB and
analogue channels.
• Confirm whether an antenna cable is connected correctly and try to tune again.
(See pages 21-23.)
• If you move the unit to a different area, you will need to perform auto tuning
again.
The TV channel which you have been
able to watch before has disappeared
and “No signal” is displayed.
RECORDING
GENERAL
The image from the external device
cannot be displayed.
• Try pressing [INPUT SELECT] repeatedly to select the external input channel,
then press [PROG. G\H] repeatedly to select your desired channel.
• Turn on all connected devices.
• Check if the connections are made securely and correctly.
DVD
Recording is impossible. • This unit cannot record programmes that contain copy protection signal. This is
not a malfunction.
• The space of the recording media may be used up. Try deleting unnecessary
titles, or exchange it with the recordable media.
• The maximum number of titles or chapters has exceeded. Delete the
unnecessary titles to make enough space or insert a new recordable media.
• Check if the disc is CPRM compatible. Copy-once programmes can only be
copied onto the disc which is CPRM compatible.
• Check if the disc is protected or finalised. Undo the protection or the finalisation.
• Video mode DVD-RW once formatted in other unit cannot be recorded in this
unit unless formatted in this unit.
• Check if the connections are made securely and correctly.
Timer recording cannot be
performed.
• The internal clock of the unit may have been stopped due to a power failure that
lasted for more than 30 seconds. Reset the clock. (See page 68.)
“Repairing” appears on the TV
screen.
• If there is a power failure or unplugging during recording, finalising, formatting or
editing (even after “Repairing” disappears), a repairing process will begin
automatically just after turning the unit on again.
• It may take several minutes up to about several hours.
In a case you intend to cancel the
repairing process.
• If you intend to cancel the repairing process, press [OPEN\CLOSE A] on the
front panel, then select “Yes” and press [ENTER\OK]. After that, press
[OPEN\CLOSE EJECT A] to take out the disc. The disc cancelled during the
repairing process MAY NOT work.
The indication
“”
does not disappear.
• “ ” may remain on screen for the maximum of
20 seconds even after it reached 100%. This is not a malfunction.
VCR
Recording does not start
immediately after pressing [REC].
• Make sure the videotape has a recorded tab when you record to a videotape. If
needed, cover the hole with cellophane tape.
Symptom Remedy
Repairing
Do you want to cancel a repairing
process? When selecting “Yes”,
the disc may not be usable.
No
Yes
Repairing
100%Writing to Disc
100%Writing to Disc
… 75 …


Need help? Post your question in this forum.

Forumrules
1

Forum

funai-wd6d-m101

Reset search

  • Can this machine be connected to a Mac computer presumably via the USB port Submitted on 27-4-2023 at 13:51

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Funai WD6D-M101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Funai WD6D-M101 in the language / languages: English as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Funai WD6D-M101

Funai WD6D-M101 User Manual - German - 84 pages

Funai WD6D-M101 User Manual - Dutch - 85 pages

Funai WD6D-M101 User Manual - Italian - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info