503729
17
Zoom out
Zoom in
Previous page
1/84
Next page
17
EN
Introduction Connections Playback Editing OthersFunction SetupRecording VCR Functions
Basic Setup /
TV View Operation
Connecting to a TV
Connect the unit to a TV after considering the capabilities of
your existing equipment.
Connect the antenna or cable to the ANTENNA
IN jack of this unit.
Connect the ANTENNA OUT jack of this unit to
the Aerial jack of your TV.
Connect AV1 (TV) Scart socket of this unit to
the Scart socket of your TV.
Note
If your TV does not have a Scart socket, use a Scart/RCA
cable to connect.
Connect this unit directly to the TV. If the AV cables are
connected to a VCR, pictures may be distorted due to the
copy protection system.
Analogue teletext can only be output in VCR mode through
AV1 (TV) out. Use TV remote control to decode the
analogue teletext.
When changing the “Video Out” setting (“SCART (RGB)”,
“Component (Interlace)” or “Component (Progressive)”),
connect to the corresponding jack on the TV. If the setting is
changed, for example, to “Component (Interlace)” or
“Component (Progressive)” while the scart cable is
connected to the TV, a distorted video signal may be output.
If your TV has component video input jacks, use a component
video cable (to connect the COMPONENT VIDEO OUT jacks)
and an audio cable (to connect the AUDIO OUT (L/R) jacks).
When using this type of connection, “Video Out” setting
should be set to “Component (Progressive)” or “Component
(Interlace)”. Refer to “B Video Out (Default: SCART (RGB))”
on page 67.
Component connection provides the better quality picture.
Connect the COMPONENT VIDEO OUT jacks of
this unit to the component video input jacks of
your TV.
Connect the AUDIO OUT (L\R) jacks of this unit
to the analogue audio input jacks of your TV.
After you have made the connections, set the “Video Out”
setting. (See page 67.)
Selecting Progressive Scan (576p/480p or
Interlaced 576i/480i) Playback
If your TV is compatible with progressive scanning (576p/
480p), connect the TV to the COMPONENT VIDEO OUT
jacks of this unit and set “Video Out” setting to “Component
(Progressive)” in “Setup” menu. (See page 67.) Next, set
your TV to the progressive scan mode.
If your TV is not compatible with progressive scan, set
“Video Out” setting to “Component (Interlace)”.
Use a commercially available adaptor if the video input jacks
of your TVs or monitors are the BNC type.
Only component and HDMI connections are compatible with
the Progressive Scan.
Connections
Before installation, unplug your TV and
this unit
Using the Scart socket
1
2
RF cable
(not supplied)
RF cable
(supplied)
Cable
Signal
or
To Aeri al ja ck
Antenna
1
2
Scart cable
(not supplied)
Scart/RCA cable (not supplied)
Audio/video cable
(not supplied)
Scart adaptor
(not supplied)
Using the COMPONENT VIDEO OUT
Jacks and the AUDIO OUT (L\R) Jacks
YPB/CB PR/CR
12
Audio IN
Component
video IN
Audio cable
(not supplied)
Component
video cable
(not supplied)
1
2
17


Need help? Post your question in this forum.

Forumrules
1

Forum

funai-wd6d-m101

Reset search

  • Can this machine be connected to a Mac computer presumably via the USB port Submitted on 27-4-2023 at 13:51

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Funai WD6D-M101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Funai WD6D-M101 in the language / languages: English as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Funai WD6D-M101

Funai WD6D-M101 User Manual - German - 84 pages

Funai WD6D-M101 User Manual - Dutch - 85 pages

Funai WD6D-M101 User Manual - Italian - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info