503763
5
Zoom out
Zoom in
Previous page
1/30
Next page
EN
5
You must attach the base to the unit to have it as a table top
unit. Be sure the front and rear of the base match the proper
direction.
To remove the base from this unit
Unscrew the Phillips pan screws on step 3. After the screws
are removed, pull the base up toward the rear of the unit. Be
careful not to drop the base when you remove it.
1 Open the battery compartment cover.
2 Insert R03/AAA 1.5V penlight batteries into battery
compartment in the direction as indicated by the
polarity (+/–) markings. Batteries installed with
incorrect polarity may damage the remote unit.
3 Close the cover.
4 Push the cover on its top side until it clicks in order to fit
the cover completely to the compartment.
Screw this unit on your furniture tightly using wood screws
(not supplied) in the 2 holes at the back of the base as shown.
Recommended screw dimension : 5.1 x 20 mm
Attaching the Base
1
Spread a thick and
soft cloth over a
table as shown. Place
the main unit face
down onto it. Make
sure not to damage
the screen.
2 Align the 2 base
hooks with the
hooks under the
bottom of the main
unit (shown by
arrow A), then slide
the base in the
direction as shown
by arrow B until it
stops and the 4
mounting holes are
aligned.
Make sure not to put
the AC power cord
between the base
and the unit.
3 Drive Phillips pan
screws into the 4
threaded holes at
the bottom of the
base until they are
tight.
Note:
• When attaching the base, ensure that all screws are tightly
fastened. If the base is not properly attached, it could cause the unit
to fall, resulting in injuries as well as damage to the unit.
• Make sure to use the table which can support the weight of this
unit and is larger than this unit.
• Make sure the table is in a stable location.
B
A
Tilt Stand
For 26” only
You can adjust the stand to change the
angle of the unit (-2° to 10°).
Installing the Batteries
Fixing the Unit on Your
Furniture
Note:
When you remove this unit make sure to unscrew the wood screws
from your Wood Stand, Furniture and other wood item.
-2°
10°
screw holes
Rear of this unit
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Funai LH840-M32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Funai LH840-M32 in the language / languages: English as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info