503524

Funai BH2-M200 Manual

69
Zoom out
Zoom in
Previous page
1/88
Next page
69
EN
Introduction Connections
Basic Setup /
DVB Operations
Recording Playback Editing Function Setup Others
Set up the network connection settings in order to use BD-
Live™ service or network update function.
After you made IP address / DNS settings or when a LAN
cable is connected, always perform the connection test to
check if the connection is correctly made.
1 Select “Connection Test”, then press
[ENTER\OK].
Connection test will start automatically and the test result
will appear right after the connection test finishes.
Press [ENTER\OK] to go to the list of network status
confirmation screen.
2 Press [ENTER\OK] to go back to the previous
screen, or press [SETUP] to exit.
Note
• If the connection test passes, you are ready to use
BD-Live™ function using the Internet without making any
extra settings.
• If the connection test fails, you may need to change the MAC
address settings on your router. You can check the MAC
address of this unit on “Network Connection” screen.
• “Connection Test” is not available when “Disable” is selected
in “Network Connection”.
Network settings are set to the following settings initially.
(In most cases, you can connect to the Internet without
making any changes to the default settings.)
If you want to set the network settings back to the default
settings as above (except “BD-Live Setting”), follow the
procedure below.
1 Select “Auto”, then press [ENTER\OK].
The unit will start the connection test automatically and
the test result will appear right after the test finishes.
Press [ENTER\OK] to go to the list of network status
confirmation screen.
2 Press [ENTER\OK] to activate the network
settings and set the network connection
automatically. Press [SETUP] to exit.
Note
• The setting of “BD-Live Setting” will not be set back to the
default, even if you follow the procedure.
In following cases, select “Manual” to set each setting as
necessary.
- When connection test failed with the setting of “Auto”.
- When instructed by your Internet service provider to make
specific settings in accordance with your network
environment.
IP Address Setting / DNS Setting
1 Select “Manual”, then press [ENTER\OK].
2 Select “IP Address Setting”, then press
[ENTER\OK].
3 Select the desired setting, then press
[ENTER\OK].
4 Press [RETURN\BACK] to go back to the
previous screen, or press [SETUP] to exit.
Network Connection
[SETUP] A “Settings” A “Others” A “Network Connection”
Connection Test
Testing... : The test is in progress.
Pass : Connection test is successfully completed.
Fail : Connection test failed.
Check the connection settings.
Auto
- IP Address Setting Auto(DHCP)
- DNS Setting Auto(DHCP)
- Proxy Setting Do Not Use
- Connection Speed Auto
- BD-Live Setting Allow
Manual
Auto(DHCP) : If your router has DHCP server function,
select “Auto(DHCP)”.
Manual : If your router does not have DHCP server
function, select “Manual”.
If you select “Manual”, follow the following
instruction to set the IP address and DNS.
If you select “Auto(DHCP)”, skip to step
4.
3-a) Select “IP Address”, “Subnet Mask” or “Default
Gateway”, then press [ENTER\OK]. IP address
setting screen will appear. Enter IP address, subnet
mask and default gateway with
[the Number buttons].
• Enter the IP address number after checking the
specifications of your router.
• If the IP address is unknown, check the IP
address of other devices. (e.g. PC connected via
LAN cable) and assign a different number from
those of other devices.
3-b) After you enter all correctly, press [ENTER\OK].
• Confirmation message will appear. Select “Yes” to
complete the settings.
3-c) Select “Primary DNS” or “Secondary DNS”, then
press [ENTER\OK]. DNS setting screen will
appear. Enter primary DNS and secondary DNS
with [the Number buttons].
• Enter the DNS addresses provided by your
Internet provider.
• If the DNS address is unknown, check the DNS
address of other devices (e.g. PC connected via
LAN cable) and assign the same DNS address.
3-d) After you enter all correctly, press [ENTER\OK].
Confirmation message will appear. Select “Yes” to
complete the settings.
'8'&A'0DQQM2CIG(TKFC[(GDTWCT[2/
… 69 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Funai BH2-M200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Funai BH2-M200 in the language / languages: English as an attachment in your email.

The manual is 2,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info