560212

Fujitsu-siemens fi-7260 Manual

105
Zoom out
Zoom in
Previous page
1/229
Next page
Chapter 5 Various Ways to Scan
Appendix
Glossary
Introduction
Index
Contents
TOP
105
How to Load
Documents
Daily Care
Troubleshooting
Operational
Settings
Replacing the
Consumables
Scanner
Overview
Various Ways to
Scan
Configuring the
Scan Settings
How to Use the
Operator Panel
2 If you open the ADF to remove the document, close it.
For details, refer to "1.4 Opening/Closing the ADF" (page 27).
3 Load the documents back in the ADF paper chute
(feeder).
If a multifeed by difference in length is detected, either press the
[Scan/Enter] button or perform a scan from the computer (do not
press the [Menu] button).
If there is an attachment which is likely to be the cause of the
multifeed error, then proceed to the next step.
4 Press the [Menu] button and confirm that the LCD displays [Do
not detect] or [Remember], and then either press the [Scan/
Enter] button or perform a scan from the computer.
From this point, note that the indication on the LCD switches between
[Detect][Do not detect] or [Remember][Do not remember] every
time you press the [Menu] button. When [Do not detect] or
[Remember] is displayed, the scanner operates in each mode as
follows:
z Manual mode (Bypass by front panel button)
Scans the next sheet without multifeed detection, and from the
second sheet, multifeeds are detected based on the setting
configured in the scanner driver or the Software Operation Panel.
z Auto mode 1 (Bypass by combination of length and position)
Memorizes the length and location of the paper attachment that
was detected as multifeed, and continues scanning. When a paper
attachment of a similar pattern is detected, multifeed detection is
automatically suppressed.(*1)(*2)
z Auto mode 2 (Bypass by length)
Memorizes the length of the longest paper attachment that was
detected as multifeed, and continues scanning. When a paper
attachment of the same length or shorter is detected, multifeed
detection is automatically suppressed.(*1)(*2)
*1: 8 overlap patterns can be memorized in this mode. When it
exceeds this limit, the first pattern that was memorized is
erased from the memory.
*2: To erase the memorized overlap patterns and the longest
overlap length, use [10: iMFF Setting] on the [Settings Menu]
screen of the operator panel, or Software Operation Panel.
After erasing is completed, the indication on the LCD changes
to or . This allows you to erase multifeed
patterns and the longest overlap length that were not
supposed to be memorized. Be careful with this operation
because all memorized patterns will be erased.
Be careful not to have your fingers caught
when closing the ADF.
ATTENTION
Confirm that the ADF is closed properly. Otherwise, the document
may not be fed into the ADF.
… 105 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujitsu-siemens fi-7260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujitsu-siemens fi-7260 in the language / languages: English as an attachment in your email.

The manual is 16,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info