560211

Fujitsu-siemens fi-7160 Manual

200
Zoom out
Zoom in
Previous page
1/229
Next page
Chapter 9 Operational Settings
Appendix
Glossary
Introduction
Index
Contents
TOP
200
How to Load
Documents
Configuring the
Scan Settings
How to Use the
Operator Panel
Various Ways to
Scan
Daily Care
Troubleshooting
Replacing the
Consumables
Scanner
Overview
Operational
Settings
Specifying an Area Not to Detect Multifeed
[Intelligent Multifeed Function]
When there is paper of the same size attached to a
designated location on the page, the scanner memorizes the
location of the attachment and can be configured not to detect
multifeeds for that location. Note that you first need to select
[Check Overlapping (Ultrasonic)] or [Check Overlapping and
length] in either the scanner driver or the multifeed detection
setting in "Specifying a Multifeed Detection Method
[Multifeed]" (page 195).
1 Start up the Software Operation Panel.
For details, refer to "9.1 Starting Up the Software Operation Panel"
(page 163).
2 From the listing on the left, select [Device Setting 2]
[Intelligent Multifeed Function].
3 Specify an operation mode.
For details about the procedure after this step, refer to "Ignoring
Multifeed for a Set Pattern" (page 103).
Mode Description
Manual mode Does not memorize the size or location of
the paper attachment when a multifeed is
detected.
Ignores the multifeed when you load the
documents back in the ADF paper chute
(feeder) and scan them again.
Auto mode 1 Memorizes the size and location of the
paper attachment when a multifeed is
detected. The memorized pattern is ignored
from the next scan.
Auto mode 2 Memorizes the size of the paper attachment
when a multifeed is detected. The
memorized pattern (including any length
less than the attachment) is ignored from
the next scan.
HINT
z By selecting the [Clear overlap pattern] check box, you can
erase the overlapping patterns (length, position) that were
memorized in Auto mode.
z By selecting the [Auto-Memorize MF Pattern (only when MF
images are displayed)] check box, you can record the multifeed
pattern on the dialog box to check an image that was detected
as multifeed.
z In [Remember multifeed pattern at power-off], you can select
whether or not to keep the multifeed pattern upon turning the
power off. When [Remember] is selected, you can use eight of
the most recent patterns the next time the scanner is powered
on.
z This setting can also be configured in the operator panel.
… 200 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujitsu-siemens fi-7160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujitsu-siemens fi-7160 in the language / languages: English as an attachment in your email.

The manual is 16,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info