560208
45
Zoom out
Zoom in
Previous page
1/211
Next page
Contents
Index
Chapter 2 How to Load Documents
Appendix
Glossary
Introduction
TOP
45
Configuring the
Scan Settings
How to Use the
Operator Panel
Various Ways to
Scan
Daily Care
Troubleshooting
Operational
Settings
Replacing the
Consumables
Scanner
Overview
How to Load
Documents
Area Not to be Perforated
An error may occur when there are punched holes in the
shaded area in the following figure. Such documents can be
scanned by using the flatbed (fi-6230Z/fi-6240Z).
Conditions for Multifeed Detection
Multifeed is an error where two or more sheets are fed through
the ADF at once. It is also called a multifeed when a different
document length is detected.
Multifeed detection is performed by either checking the
overlapping of documents, length of the documents, or the
combination of both. The following conditions are required for
an accurate detection.
Detection by overlapping
z Load documents of the same paper weight in the ADF paper chute.
z Paper weight: 41 to 209 g/m² (11 to 56 lb)
z Do not punch holes within 35 mm (1.38 in.) over the center of the
document. See Fig.1.
z Do not attach other documents within 35 mm (1.38 in.) over the
center of the document. See Fig.1.
Detection by length
z Load documents of the same length in the ADF paper chute.
z Variance in document lengths: 1% or less
z Do not punch holes within 35 mm (1.38 in.) over the center of the
document. See Fig.1.
Detection by overlapping and length
z Load documents of the same paper weight and length in the ADF
paper chute.
z Paper weight: 41 to 209 g/m² (11 to 56 lb)
z Variance in document lengths: 1% or less
z Do not punch holes within 35 mm (1.38 in.) over the center of the
document. See Fig.1.
z Do not attach other documents within 35 mm (1.38 in.) over the
center of the document. See Fig.1.
The above condition applies when the document is set to the
center of the pick roller width.
If there are any holes in the 35 mm-wide central column, you
can move the document to the left or right to avoid an error.
( Unit : mm)
Top
Reference point
Front side
Feed
direction
Bottom
35
Center
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujitsu-siemens FI 6240 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujitsu-siemens FI 6240 in the language / languages: English as an attachment in your email.

The manual is 18,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info