510515

Fujitsu-siemens Fi 6110 Manual

157
Zoom out
Zoom in
Previous page
1/179
Next page
Chapter 9 Operational Settings
Appendix
Glossary
Introduction
Index
Contents
TOP
157
How to Load
Documents
Configuring the
Scan Settings
How to Use the
Operator Panel
Various Ways to
Scan
Daily Care
Troubleshooting
Replacing the
Consumables
Scanner
Overview
Operational
Settings
Specifying an Area Not to Detect Multifeed
[Intelligent Multifeed Function]
When there is paper of the same size attached to a
designated location on the page, the scanner memorizes the
location of the attachment and can be configured not to detect
multifeeds for that location. To configure this setting, you first
need to select [Check Overlapping (Ultrasonic)] or [Check
Overlapping and Length] in either the scanner driver’s setup
dialog box or the multifeed detection setting in "Method of
Multifeed Detection [Multifeed]" (page 152).
1 Start up the Software Operation Panel.
Refer to "9.1 Starting Up the Software Operation Panel" (page 132).
2 From the listing on the left, select [Device Setting 2] J
[Intelligent Multifeed Function].
3 Select an operation mode and click the [OK] button.
For details about the procedure after this step, refer to "Ignoring
Multifeed for a Set Pattern" (page 89).
Mode Description
Manual mode Stops feeding the documents when a
multifeed is detected. You can resume
scanning by loading the documents back in
the ADF paper chute.
The size and location of the attachment are
not memorized.
Auto mode 1 Memorizes the size and location of the
paper attachment upon resuming the scan
when a multifeed is detected and the
document is loaded back in the ADF paper
chute. The memorized pattern is ignored
from the next scan.
Auto mode 2 Memorizes the size of the paper attachment
upon resuming the scan when a multifeed is
detected and the document is loaded back
in the ADF paper chute. The memorized
pattern is ignored from the next scan.
z By selecting the [Clear overlap pattern] check box, you
can erase the overlapping patterns (length, position)
that were memorized in Auto mode.
z In [Remember multifeed pattern at power-off], you can
select whether or not to keep the multifeed pattern
upon turning the power off. When [Remember] is
selected, you can use eight (pages worth) of the most
recent patterns the next time the scanner is powered
on.
… 157 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujitsu-siemens Fi 6110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujitsu-siemens Fi 6110 in the language / languages: English as an attachment in your email.

The manual is 15,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info