693468
11
Zoom out
Zoom in
Previous page
1/14
Next page
11
WW_EN
Troubleshooting
Please check the following items before considering a problem to
be a malfunction. If the problem persists even after taking action,
please contact the FUJIFILM service center for repair in your
country or visit the website below.
FUJIFILM website: http://www.fujifilm.com/
If the following problem occurs���
Problem Possible causes and solutions
I cannot turn on
the printer.
The battery may not be charged. Please
charge the printer.
You did not press the Power button for
long enough. Press and hold the Power
button for approximately 1 second.
The battery
loses its charge
quickly.
If you use the printer in a very cold
environment, the battery will drain quickly.
Please keep the printer warm before
printing.
The power cut
off during use.
The battery level may be low. Please charge
the printer.
Charging does
not start.
Make sure that the USB power adapter plug
is properly connected to the power outlet.
The printer takes
too long to
charge.
At low temperatures, charging may take
longer.
Charging stops
during charging.
Charge the battery in a temperature range of
+5 °C to +40 °C. If you cannot charge the
printer in this range, contact your FUJIFILM
dealer or support center.
The printer does
not function
normally.
There may be a temporary malfunction.
Please press the reset button. If the printer
still does not function normally, please
contact our repair service center for repair.
The battery may not be charged. Please
charge the printer.
The film pack
does not load or
does not load
correctly.
Please use FUJIFILM instax mini Instant
Film (other films cannot be used).
Align the yellow mark on the film pack
with the yellow alignment marker on the
printer body, once aligned load the film
into the printer.
The film does
not unload.
The film may be misaligned due to shock
such as vibration or dropping. Please load
a new film pack.
If the film is jammed, turn the printer off
and turn it on again. If the problem
persists, remove the jammed film and
then load a new film pack.
Some or all of
the finished
prints are white.
Do not open the film door until the film has
been used up. If the film door is opened with
film remaining, the film will be exposed and
become white.
Specifications
Recording method 3-color exposure with OLED
Film used FUJIFILM instax mini Instant Film (sold
separately)
Number of films 10 films/pack
Image size 62 mm × 46 mm
Supported image
size
800 × 600 dots
Printing resolution 12.5 dots/mm (318 dpi, 80 μm dot pitch)
Printing levels 256 levels per color (RGB)
Interface Standard compliance: Bluetooth Ver. 4.2
(BLE)
Supported image
format
JPEG, PNG, HEIF
Printing time Image recording - photo output (fed out):
Approximately 12 sec.
Approximate
printing capacity
Approximately 100 prints (from full
charge)
* The number of prints depends on the
usage conditions.
Power supply Lithium ion battery (internal type: not
removable)
Charging time Approximately 80 to 120 minutes
(Charging time depends on the
temperature and battery remaining level)
Power consumption Approximately 3 W
Operating
environment
Temperature: +5 ºC to +40 ºC
Humidity: 20% to 80% (no condensation)
Main unit
dimensions
90.3 mm × 34.6 mm × 124.5 mm
(excluding projecting parts)
Main unit mass Approximately 209 g (excluding film
pack)
Supplied accessory USB cable (BOD700, Length: 30 cm)
*The above specifications are subject to change for performance
improvement.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujifilm Instax Mini Link - Smartphone printer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujifilm Instax Mini Link - Smartphone printer in the language / languages: English as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fujifilm Instax Mini Link - Smartphone printer

Fujifilm Instax Mini Link - Smartphone printer User Manual - German - 14 pages

Fujifilm Instax Mini Link - Smartphone printer User Manual - Dutch - 14 pages

Fujifilm Instax Mini Link - Smartphone printer User Manual - French - 14 pages

Fujifilm Instax Mini Link - Smartphone printer User Manual - Italian - 14 pages

Fujifilm Instax Mini Link - Smartphone printer User Manual - Spanish - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info