101549
61
Zoom out
Zoom in
Previous page
1/65
Next page
121
There is speckling on
the image.
The camera does not
emit any sound.
Frame erase does not
erase the frame.
The ERASE ALL
function does not erase
all the frames.
Screens are not
displayed in English.
There is no image or
sound on the TV.
When the camera is
connected to a personal
computer (PC), the
photographed image or
playback image appears on
the camera’s LCD monitor.
Nothing happens when
I use the Mode dial.
The camera no longer
works correctly.
Can’t print with
PictBridge.
The camera was
connected to PC when
the USB mode was set
to “
ˆ
”.
The picture was taken with a slow shutter
speed (long exposure) in a high-
temperature environment.
i The camera volume is set too low.
i The microphone was blocked during
shooting/recording.
i There is something covering the speaker
during playback.
Some frames may be protected.
i A language other than English is
selected in the “ ” setting in
SET-UP (P.86).
i The included A/V cable was connected
during movie playback.
i
The camera is not connected to the TV
correctly.
i “TV” is selected as the TV input.
i The video output setting is incorrect.
i The TV volume is turned down.
i The USB cable is not correctly
connected to the PC or camera.
i The PC is not turned on.
i Camera malfunction.
i The battery runs out.
The camera has suffered an unforeseen
problem.
ˆ
” is not selected in USB mode in the
SET-UP menu.
This is a characteristic of CCDs and does
not indicate a camera fault.
i Adjust the volume.
i Take care not to block the microphone
during shooting/recording.
i Make sure that the speaker is uncovered.
Unprotect frames using the camera on
which the protection was first applied.
1Press the “MENU/OK” button to display
the menu.
2Press “dor “cto select “
F” and press
a” or “b” to select “SET-UP”. (Press the
“MENU/OK” button to appear the SET-
UP screen on the LCD monitor.)
3Press “d” or “c” to move to option 3 and
then use “a” or “b” to select “ ”.
4Press “d” or “c” several times to select
“ENGLISH”.
5Press the “MENU/OK” button.
i After the movie playback mode is stopped,
connect the camera and TV correctly.
i Connect the camera and TV correctly.
i Set the TV input to “VIDEO”.
i
Change the setting to “NTSC” or “PAL” (P.86).
i Adjust the volume.
i Set up the camera and the USB cable
(included) correctly.
i Turn the PC on.
i
Briefly remove the battery or disconnect the
AC power adapter. Then reload the battery or
reconnect the AC power adapter and try again.
i Load a new or fully charged battery.
Briefly remove the battery or disconnect
the AC power adapter. Then reload the
battery or reconnect the AC power adapter
and try again.
If the message still appears,
contact your FUJIFILM dealer.
Select “
ˆ
” in USB mode in the SET-UP
menu.
Perform steps
1
to
3
to remove the
camera from PC.
h Windows
1
The “New Hardware Found” wizard (or
“Scanner and Camera” wizard) appears. If the
wizard does not appear, proceed to step
3
.
2
Click the [Cancel] button.
3
Disconnect the camera from the PC.
h Macintosh
1
The window for locating the driver
appears. If the window does not
appear, proceed to step
3
.
2
Click the [Cancel] button.
3
Disconnect the camera from the Macintosh.
Troubleshooting Possible causes Solutions
120
Troubleshooting eIf you think the camera is faulty, check the following once more.
The viewfinder lamp
does not light when
charging the battery.
The viewfinder lamp
blinks during charging
and the battery won’t
charge.
No power.
Power cuts out during
operation.
Battery runs out quickly.
No photograph is taken
when the Shutter button
is pressed.
Can’t use the flash.
The flash settings are
restricted and cannot
be selected.
Can only select
Suppressed flash
mode.
Can only select the
1
” and “
¡
” quality
settings.
The playback image is
dark even though the
flash was used.
The image is blurred.
i There is no battery in the camera.
i The camera and AC power adapter are
not connected correctly.
i The battery terminals are dirty.
i The battery gets un-rechargeable.
i The battery has runs out.
i The AC power adapter plug has come
out of the power outlet.
i The battery is loaded backward.
i The battery cover is not closed correctly.
The battery runs out.
i Camera is being used in extremely cold
conditions.
i The terminals are soiled.
i The battery get un-rechargeable.
i No xD-Picture Card is inserted.
i The xD-Picture Card is fully recorded.
i The xD-Picture Card is not formatted.
i The xD-Picture Card contact area is
soiled.
i The xD-Picture Card is damaged.
i The Auto power off function has turned
the camera off.
i The battery runs out.
i The Shutter button was pressed while
the flash was charging.
i The flash is not popped up.
i The Mode dial is set to “
,
” Landscape.
i Continuous shooting is selected.
The Mode dial is set to “
m
”, “
,
”, “
.
” or
/
”.
Continuous shooting is selected.
The sensitivity is set to 1600 (high-
sensitivity photography).
i The subject is too far away.
i Your finger was covering the flash/flash
control sensor.
i The lens is dirty.
i You photographed scenery with Macro
mode selected.
i You took a close-up shot without
selecting Macro mode.
i You are shooting a subject that is not
suited to autofocusing.
i Load the battery.
i Connect the camera and AC power
adapter correctly.
i Take the battery out briefly and then
reload it.
i Wipe the battery terminals with a clean,
dry cloth.
i Load a new battery. If the battery still
fails to charge, contact your FUJIFILM
dealer.
i Load a new or fully charged battery.
i Plug the adapter back in.
i Load the battery in the correct direction.
i Close the battery cover correctly.
Load a new or fully charged battery.
i Put the battery in your pocket or another
warm place to heat it and then load it into
the camera just before you take a picture.
i Wipe the battery terminals with a clean,
dry cloth.
i Load a new battery.
i Insert an xD-Picture Card.
i Insert a new xD-Picture Card or erase
some unwanted frames.
i Format the xD-Picture Card on the
camera.
i Wipe the xD-Picture Card contact area
with a clean dry cloth.
i Insert a new xD-Picture Card.
i Turn the camera on.
i Load a new or fully charged battery.
i Wait until the flash has finished charging
before pressing the Shutter button.
i Pop up the flash.
i Change the Photography mode.
i Set continuous shooting to “OFF”.
The flash settings are restricted because
the camera settings are tailored to the
scene being shot. Change the Photography
mode for a wider range of flash settings.
Set continuous shooting to “OFF”.
Set the sensitivity to 800 or less.
i Move to within the effective flash range
before taking the picture.
i Hold the camera correctly.
i Clean the lens.
i Cancel Macro mode.
i Select Macro mode.
i Use AF/AE lock to take the picture.
Troubleshooting Possible causes Solutions
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujifilm Finepix F710 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujifilm Finepix F710 in the language / languages: English as an attachment in your email.

The manual is 6,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info