101074
53
Zoom out
Zoom in
Previous page
1/58
Next page
105104
I cant use the flash to
take pictures.
The flash will not charge.
The playback image is
too dark even though I
used the flash.
The image is blurred.
I cannot format the
SmartMedia.
I cannot erase all the
frames.
The Mode dial has been moved to another
setting.
The flash is set to Suppressed Flash
mode (The flash is closed).
You pressed the shutter button while the
flash was charging.
No compatible SmartMedia is loaded.
The camera is set to Suppressed Flash
mode.
The camera is set to Macro Photography.
The battery is exhausted.
The subject is too far away.
Your finger covering the flash.
The lens is dirty.
The lens is zoomed to telephoto in Macro
mode.
The SmartMedia is write-protected.
The frame is protected.
Set the Mode dial to the correct setting.
Set the flash to Auto, Red-Eye Reduction or
Forced Flash mode (Pop the flash unit up).
Wait until charging is completed before
pressing the shutter button.
Load a new SmartMedia, erase a frame,
or remove the write-protection.
Set the flash to Auto, Red-Eye Reduction
or Forced Flash mode.
Cancel Macro Photography.
Load a new battery.
Move closer to the subject.
Hold the camera correctly.
Clean the lens.
Cancel Macro mode.
Remove the write-protection.
(Peel off the write-protect sticker.)
Remove the frame protection.
Cause RemedyProblem
Troubleshooting eIf you think the camera is faulty, check the following once more.
No power
Power cuts out during
operation.
Battery runs out quickly.
No photograph is taken
when the shutter button
is pressed.
Load a new fully charged battery.
Plug the adapter back in.
Load a new fully charged battery.
Wipe the battery terminals with a clean,
dry cloth before charging.
Put the battery in your pocket or another
warm place to heat it and then load it into
the camera just before you take a picture.
Wipe the battery terminals with a clean,
dry cloth before charging.
Load a new fully charged battery.
Use Ni-MH or Ni-Cd batteries.
Load a SmartMedia.
Load a new SmartMedia or erase a
frame.
Remove the write-protection.
Format the SmartMedia.
Wipe the SmartMedia contact area with a
clean dry cloth.
Load a new SmartMedia.
Switch the camera on.
Load a new fully charged battery.
Problem Cause Remedy
The battery is exhausted.
The AC power adapter plug has come out
of the power outlet.
The battery is exhausted.
The terminals are soiled.
You are using the camera in extremely
cold conditions.
The terminals are soiled.
The battery is flat.
You are using alkaline batteries.
No SmartMedia is loaded.
The SmartMedia is fully recorded.
The SmartMedia is write-protected.
The SmartMedia is not formatted.
The SmartMedia contact area is soiled.
The SmartMedia is damaged.
The Auto Power Off function has switched
the camera off.
The battery is exhausted.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujifilm Finepix 40I at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujifilm Finepix 40I in the language / languages: English as an attachment in your email.

The manual is 2,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info