540674
22
Zoom out
Zoom in
Previous page
1/67
Next page
Ask your dealer to instruct you in correct wheel removal and installation, and ask him to give you any available
manufacturers instructions.
WARNING: Riding with
an improperly secured wheel can allow the wheel to wobble or fall off the bicycle, which
k your wheels safely.
dropouts.
ondary wheel retention device to reduce the risk of the wheel disengaging
from
ondary retention devices fall into two basic categories:
the front wheel hub or front fork.
.
s name implies, it serves as a back-up
ms
enter cam wheel retention mechanisms: the traditional over-center cam (fig. 8a) and
the
r cam pushing against one dropout and pulling the tension
adju
can cause serious injury or death. Therefore, it is essential that you:
your dealer to help you make sure you know how to install and remove
1. As
2. Understand and apply the correct technique for clamping your wheel in place.
3. Each time, before you ride the bike, check that the wheel is securely clamped.
The clamping action of a correctly secured wheel must emboss the surfaces of the
1. Front Wheel Secondary Retention Devices
Most bicycles have front forks which utilize a sec
the fork if the wheel is incorrectly secured. Secondary retention devices are not a substitute for correctly securing your front
wheel.
Sec
a. The clip-on type is a part which the manufacturer adds to
b. The integral type is molded, cast or machined into the outer faces of the front fork dropouts
Ask your dealer to explain the particular secondary retention device on your bike.
WARNING: Do not remove or disable the secondary retention device. As it
for a critical adjustment. If the wheel is not secured correctly, the secondary retention device can reduce the risk
wheel disengaging from the fork. Removing or disabling the secondary retention device may also void the
warranty. Secondary retention devices are not a substitute for correctly securing your wheel. Failure to properly
secure the wheel can cause the wheel to wobble or disengage, which could cause you to loose control and fall,
resulting in serious injury or death.
2. Wheels with cam action syste
of the
There are currently two types of over-c
cam-and- cup system (fig. 8b). Both use an over-center cam action to clamp the bike’s wheel in place. Your bicycle may have
a cam-and-cup front wheel retention system and a traditional rear wheel cam action system.
a. Adjusting the traditional cam action mechanism (fig. 8a)
The wheel hub is clamped in place by the force of the over-cente
sting nut, by way of the skewer, against the other dropout. The amount of clamping force is controlled by the tension
18
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fuji Bike at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fuji Bike in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info