535711
8
Zoom out
Zoom in
Previous page
1/78
Next page
8
INTRODUCTION AND
OVERVIEW
MULTIPLE USERS
The system allows for up to 8 Users, a Master
(Admin) and 7 Users to be configured. This
allows the system Event Log to maintain a
record of which users have armed and disarmed
the system. Each user will have a different User
Access PIN Code.
Only the Admin User has access to the
programming functions and is able to configure
the system.
USER ACCESS PIN CODE
The Control Panel is the brains of the system
and is where the system is programmed and
operated from. A 4 digit PIN code is used to
ensure that only authorized people have access
to the system. This is the User access PIN code
and can be set to a code of your choice that only
you and other authorized system users know.
SYSTEM ARMING
The system has a ‘Fully Arm, two ‘Part-Arm
and a ‘Holiday Armmodes. Fully Arm and
Holiday Arm will ‘Arm’ all zones while the ‘Part-
Arm’ modes will only arm the zones that are
enabled for the particular Part-Arm mode.
For example:
The system could be configured so that during
night time, ‘Part-Arm-I’ would arm only zones
protecting the lower floor and outbuildings
leaving the upper floor free for movement
without triggering the alarm.
During the day while the property is occupied
‘Part-Arm-II’ could arm only the zones protecting
the outbuildings. However, when the property is
left un-occupied, the ‘Fully Arm’ mode will arm
all zones to protect the entire property, (i.e.
upper and lower floors and outbuildings).
ENTRY/EXIT DELAY
When the system is armed with the Exit-Delay
enabled, no signal from any detector on an
active zone will be able to trigger an alarm until
the Exit-Delay has expired. This enables the
system to be armed from within the property and
allows time for the user to exit the property
without triggering an alarm. If the Exit-Delay is
disabled then detectors on active zones will
immediately be able to trigger an alarm once the
system is armed.
Zones1&2 only have been pre-configured
with an entry/exit delay of 30 seconds
because detectors added on these zones are
Fully & Holiday Arm
Part-Arm-I
Part-Arm-II
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Friedland HISK1 GlobalGuard Alarm System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Friedland HISK1 GlobalGuard Alarm System in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info