664132
30
Zoom out
Zoom in
Previous page
1/48
Next page
30
WEEKLY
SIX MONTHS
ANNUALLY
LUBRICATION
Check the following and adjust as necessary:
Note:
Arm rest tightening knobs (see page 7 )
Tyre pressures (see technical specification page 36)
Battery fastening strap (see page21)
Allow battery charger to go through a full recharge cycle
until the green light is illuminated (see page 24-28 )
Clean paintwork with auto shampoo.
Wax painted and bright metal parts.
Tyre wear, replace as necessary (minimum tread 0.5mm)
All fasteners and fittings for sound function
Tension of handle bar lock and hinge bolt
Battery connections
Inspect all electrical plugs and sockets for damage and
good contact and fit.
Wig-wag accelerator lever pivot point (see Fig 37)
Do not use a high
pressure hose
Check and adjust as necessary:
Lubricate the following:
Check the following and adjust as necessary:
.
Spray metal parts with moisture repellent (Wd40)
Seat lock lever pivot bolt
Seat arm hinges
Inspect, lubricate and adjust upper handle bar steering
bearings
Motor carbon brush wear (minimum brush length 8mm)
Front wheel bearings for wear
Chassis for sound welds
Rear Drive wheel hub keys
All wheel bolts
Drive axle securing bolts
Motor mounting bolts
Magnetic motor brake disc and function
Manual brake shoe lining wear
Main control box electrical connections
Main wiring loom for damage
All steering components
Clean chassis and repaint any exposed parts
Lubricate on/off power key barrel with light oil
Replace any damaged axle seals
Cycle test charger for full operation function
Cycle test batteries for operating capacity (This test can be
performed by your Freerider Agent)
the items listed under weekly and six months inspection
should be incorporated into this annual inspection.
Use a general purpose light lubricating oil on moving parts.
All wheel bearings are factory sealed and should not
normally need lubricating.
Your drive axle is factory filled with a special lubricant and
will not normally need replacing.
WEEKLY
SIX
MONTHS
ANNUALLY
Check
the following and adjust as necessary:
Note:
Do not
use a high
pressure
hose
Check
and adjust as necessary:
Lubricate
the following:
Check
the following and adjust as necessary:
FIG 37
Caution:
STEERING COLUMN ADJUSTMENT
RECOMMENDED AREAS FOR ADJUSTMENT
Do not mix other lubricants with this factory fitted
drive axle lubricant. Failure to observe this caution will
invalidate your guarantee.
The steering column locking system works on a 'cam'
principle to lock the column in the desired driving position
(see fig 38 ).
If you notice the column is not firmly held when the black
cam operating lever is fully down, follow this procedure to
readjust the 'cam' tension:
1. Push steering column forward as far as it will go with the
locking lever released, i.e. pushed upwards. Support
steering column.
2. With a 10mm spanner (not supplied) loosen the locking
nut positioned on the opposite side to the black locking
lever .
3. Next to the locking nut is a chrome threaded 'clamping
nut' this has a slightly tapered shape. Turn this clamping
nut clockwise approximately a quarter of a turn.
4. Push the 'black' clamping lever down and test that the tiller
is tightly held in place; adjust 'clamp nut' until correct
tension is achieved on clamp plates.
5. Tighten locknut with 10mm spanner.
Please note: These service intervals are a guide, more
frequent use of your Scooter may require adjustment to these
suggested intervals.
Do not drive your Scooter with the steering handlebars
unlocked or poorly adjusted.
Caution:
STEERING
COLUMN ADJUSTMENT
Do
not
Please
note: These service intervals are a guide, more
frequent
use of your Scooter may require adjustment to these
suggested
intervals.
RECOMMENDED AREAS FOR ADJUSTMENT
FIG 38
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Freerider FR510DXXsb at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Freerider FR510DXXsb in the language / languages: English as an attachment in your email.

The manual is 2,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info