664127
23
Zoom out
Zoom in
Previous page
1/48
Next page
23
Other hand, lift the seat post vertical until the front and
rear sections have separated.
This operation is made easier if you first lower
and lock the tiller. You will find the front section is
better balanced in this position.
Please keep the rear chassis level at all times during
the de-docking operation, failure to observe this caution will
result in the two sections jamming together.
The Scooter is now dismantled into its 6 basic parts (Fig 29).
The Seat Rear Motive Powered Unit
The Batteries Steering Platform
The Basket Rear Cover
You can now load your Scooter into a suitable car.
Protect clothing when lifting Scooter parts, some
components may have lubricating fluids on their surfaces.
Work out the best practice to stow each part of your
machine, this will vary with different car designs. An old
blanket can be used to stop the various parts rubbing against
each other.
NOTE:
It is good practice to stand the batteries upright and locate
them so they do not fall over and touch the battery posts on
any metal framework. Your Scooter will increase the
load in Your car, please remember this and adjust your
driving to suit this condition.
In some midsize cars the scooter seat may need to be
stowed on the front seat of the vehicle. Use the cars safety
belt to secure the seat in position.
The body mouldings on your Scooter have not
been designed for lifting your machine. Use the firm metal
lifting handles only.
Take care when lifting heavy parts. If in doubt
always seek assistance when lifting parts in or out of your
vehicle.
Note:
Caution:
Caution:
Caution:
Warning:
14
25
36
NOTE:
Caution:
Caution:
Note:
Caution:
Warning:
FIG 31
1 4
2
3
5
6
Your Scooter is very easy to re-assemble once you reach your
destination. To re-assemble, follow the preceding procedure
in reverse order, noting the following:
1. When re-assembling the front and rear sections of your
Scooter, make certain you are on firm, level
ground. Place the front and rear units close together
with the round tube of the front steering section facing
with the 'U" Shaped channel of the rear motive unit.(see
fig 30 on page 22)
With one hand support the rear motive unit at the 'C'
shaped handle keeping it level. With your other hand lift
the rear of the front steering section by the seat post and
lower it into the 'U' shaped channel, simultaneously
locate the locking pins brackets together.
Fit the safety locking pin (fig28, page 22) through the
location holes, make certain that the spring loaded safety
'clip' is firmly located into the safety "locking pin" (see fig
29 page22)
Failure to engage these safety pins correctly could
result in an accident, please take particular care.
2. Connect the electrical plugs correctly together.
you ay have them the wrong
way round, observe the locating groove in each
connector.(see fig 23, fig 26/27, page 21/22)
3. When you have replaced the batteries make certain that
they are correctly strapped down (see fig22,page21)
The battery straps simply locks together via the velcro
adhesive technique.
4. When you have re-assembled your Scooter and
fitted the rear cover and seat, switch the power key to
the 'on' position. The battery level gauge on your
console ( fig11, page 9 ) will illuminate. This will
indicate that you have re-connected the battery
connectors correctly. If the battery level gauge does not
function, then you have not connected the wiring
connectors correctly ( fig 23, fig26/27,page 21/22).
Test the drive function of your machine. Does your
Scooter move forwards and backwards correctly ? If
your Scooter does not drive, the freewheel lever may be
in the 'disengaged' position (9 bars flashing), see section
'Freewheeling your Scooter in this manual.
Your Scooter has been designed for
pavement and road use only,
DO NOT FORCE TOGETHER
Important notice:
IT IS NOT A DIRECT
REPLACEMENT FOR A SEAT IN A MOVING VEHICLE.
HOW TO RE-ASSEMBLE YOUR SCOOTER
Now enjoy your Freerider.
Warning:
HOW TO RE-ASSEMBLE YOUR SCOOTER
Warning:
DO
NOT FORCE TOGETHER
Important
notice:
IT
IS NOT A DIRECT
REPLACEMENT
FOR A SEAT IN A MOVING VEHICLE.
Now enjoy your Freerider.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Freerider FR510DXs2b at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Freerider FR510DXs2b in the language / languages: English as an attachment in your email.

The manual is 2,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info