510203
11
Zoom out
Zoom in
Previous page
1/48
Next page
9
GB
b. Before tting the chimney to the canopy make the electrical connection as described in the section
titled ELECTRICAL.
c. Each chimney stack consists of two sections. Fit the upper sections (Fig. 2a - item 7) rst by ex-
panding the chimneys slightly around the bracket and secure the chimney stacks to the brackets using
the M4 screws provided.
d. Check the vertical of the chimney.
e. Pull on the lower chimney item 5 and secure it temporarily unscrewing a little bit the lower self tap-
ping screws as illustrated in Fig 9.
IN THE RECIRCULATION MODE:
a. Fit the recirculation spigot R onto the chimney bracket using the same xing screws.
b. Connect the ducting 150mm (6 INS) not provided between motors item 6 and the recirculation spigot
and secure the connections with appropriate clamping rings or adhesive tape (Fig. 6).
c. Before tting the chimney to the canopy make the electrical connection as described in the section
titled ELECTRICAL.
d. Each chimney stack consists of two sections. Fit the upper sections (Fig. 2a - item 7) rst by
expanding the chimneys slightly around the bracket and secure the chimney stacks to the brackets using
the M4 screws provided.
e. Check the vertical of the chimney.
f. Pull on the lower chimney item 5 and secure it temporarily unscrewing a little bit the lower self tap-
ping screws as illustrated in Fig 9.
• FITTING THE CANOPY ONTO THE CHIMNEY
10) Place the canopy under the chimney and x it with the 6 TH 5X16 screws provided as illustrated in
Fig. 10. Attention: 2 persons are necessary to secure this operation.
11) Screw the lower self tapping screws of the upper chimney and t the lower chimney section item 5
by expending slightly it onto the canopy .
12) Connect the connector, check the connectors of the motor and place the cover as illustrated in Fig.
11.
13) Test the lights and the fan motor.
14) Remove the metal grease lters. Insert the charcoal lter into the base of the motor housing and
secure the lter with two securing straps A as illustrated Fig. 6.
15) Fit the metal grease lters.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Franke Florida Centrale at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Franke Florida Centrale in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 39,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info