686544
11
Zoom out
Zoom in
Previous page
1/14
Next page
Frama F-Link
20
3.10 Configuration Page Administration F-Link Log
The F-Link writes an operation log file. You can display the log entries when you open the configuration
page Administration F-Link Log and press the button Refresh.
Frama F-Link
21
4 Troubleshooting
4.1 No access to the configuration pages
When the access to the configuration pages is not possible then different reasons are possible.
1. Network errors
Are you sure that you use the right IP address for the F-Link?
Try a ping to the IP address of the F-Link from the console of a PC in the same network (if ping is
working in your network). When you get no answer from the F-Link then check your network.
2. Proxy configuration errors
It is possible that you use a Proxy server in your network for internet browsing. You must config-
ure the proxy settings of your PC that the local IP address of F-Link is bypassed / excluded by the
proxy server.
3. Login fails / lost login values
If you don’t know the username and password for the F-Link configuration page access anymore,
you can reset the F-Link. After the reset the administrator username and password are on the de-
fault values username: “admin” and password: “admin”.
4. No access by default IP 192.168.1.200
If the F-Link was used before for connections with LAN connection type DHCP or STATIC the ac-
cess over the default IP address 192.168.1.200 is not possible. Perform a reset of F-Link without a
connected network cable (see chapter 4.5). The default IP 192.168.1.200 is now active again for
a configuration by a direct LAN cable connection.
4.2 Old configuration page values
Internet web browsers store data from web pages for offline mode and caches data to show web pages
faster. It is possible that not the actual data are displayed on a configuration page of F-Link. You can clear
the offline and cached data of your browser normally over a menu entry of the browser. Restart the
browser after you clear the offline and cached data and try again.
4.3 F-Link LED status
The different status of the LED’s from F-Link are described in the installation manual
[F-Link Installation Manual, Order-Nr: 1018863].
4.4 No access to Frama FO2 backend server
For a successful connection to the Frama FO2 backend server the following network configurations are
required:
Open firewall ports:
53 DNS
443 HTTPS
Allow access to URL:
fo2.frama.com
The IP address of the URL fo2.frama.com can be found either by using the ping command “ping
fo2.frama.com” in a command line window (if ping is allowed in your network) or by a DNS lookup ser-
vice in the internet.
Proxy servers using SSL-interception require a specific rule in order to allow transparent communication
(franking system via F-Link to FramaOnline2) via https port 443.
The specific rule grants correct identification of FramaOnline2 (https certificate) for the franking system.
4.5 Reset the configuration
The configuration of the F-Link can be reset. Disconnect the LAN cable from F-Link. Press the RESET switch
at the back of the device for a minimum of 10 seconds. After this process the F-Link restores the factory
configuration and all previous configuration settings will be lost. After the reset, the F-Link reboots and is
ready to be reconfigured when the Ready LED is on again.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frama F-Link at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frama F-Link in the language / languages: English as an attachment in your email.

The manual is 2,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info