779802
23
Zoom out
Zoom in
Previous page
1/28
Next page
EN
MALFUNCTIONS
DANGER:
Before any operation after a malfunction has occurred:
- Switch off the machine.
- Remove the plug from the socket.
- Wait until bandsaw saw blade is still.
After any operation, put all safety devices into service and check them.
PROBLEMS
CAUSES
SOLUTIONS SUGGESTED
The engine does not work
A possible tension reduction
has made the minimum
voltage relay start.
- Re-start the machine.
There is not any supply voltage:
- Check the cable, the socket and the switch.
Motor overheating, due for
example to a smoothed blade
or to accumulation of saw dust
inside the carter:
Find a remedy to the cause of overheating, let
the machine cool down, and then re-start it.
Bandsaw saw blade moves
away from the cutting line or
decentralizes itself
Bandsaw saw blade is not
centred on the driving wheel:
Modify upper wheel angle.
Bandsaw saw blade has
broken
Saw blade tension is
unsuitable:
- Adjust saw blade’s tension.
Cutting pressure is too high:
- Reduce the pressure applied to the saw
blade.
Bandsaw saw blade is
unsuitable:
- Replace bandsaw saw blade:
- If you must cut a thin workpiece, you must
use a thin saw blade.
- If you must cut a wide workpiece, you must
use a wide saw blade.
The saw blade is misshapen
Cutting pressure is too high:
Avoid to extert a lateral pressure on the
bandsaw saw blade.
During work, the bandsaw
stops
Cutting pressure is too high:
- Reduce the pressure you are exerting on the
workpiece.
- Check saw blade sharpness and features.
Strong bandsaw vibrations:
Insufficient fastening:
Firmly fasten the bandsaw to a suitable
ground.
The workbench is loose:
Place the workbench and fix it.
Motor fixing is loose:
Check lock screws and tighten them if
necessary.
Aspiration coupling is
obstructed
No dust collection device is
connected or aspiration duct is
too small.
Connect the dust collection device or increase
aspiration power (air speed 20 m/sec at the
level of the dust collection coupling).
AFTER-SALES SERVICE
All tools and accessories are made and checked by using the safest and most modern productive methods.
However, if despite these attentions a tool gets damaged, it must be repaired by a Femi authorised after sales
centre.
You can send a request to the e-mail address info@fox-machines.com.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fox F28-182A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fox F28-182A in the language / languages: English as an attachment in your email.

The manual is 1.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info