783496
10
Zoom out
Zoom in
Previous page
1/108
Next page
www.foodsavereurope.com 10
Troubleshooting
Problem Solution
The Instant Seal light is flashing
when trying to seal. Under very heavy usage, this will happen to prevent overheating. If this happens wait 20 minutes to
allow appliance to cool off. During use, always wait at least 20 seconds before you begin vacuum
packaging another item.
Pump operates for more than 2
minutes without air being removed. Make sure the open end of the bag is inserted into the drip tray within the lower gasket area.
Check to make sure both gaskets are fitted properly and not damaged.
Check to make sure that at least one end of the bag is sealed.
Open the unit and check to make sure that there are no foreign objects, dirt or debris on the upper or
lower gaskets.
Make sure there is enough room at the top of the bag (75 mm) so it will fit into the drip tray with lid
closed and latched.
Make sure the accessory hose is not attached.
Make sure the lid is fully closed with the latch in the closed position
.
Bag is not sealing properly. There is moisture or grease in the bag at the sealing point. Wipe away any excess moisture with a
clean, dry paper towel.
There is too much liquid in the bag. Freeze the bag contents before vacuuming.
There is a crease on the seal line. Gently stretch the bag flat while inserting the bag into the drip tray
and continue to hold bag until vacuum pump starts. If this has already been done and the bag still
does not seal, create a second seal above the first one.
Nothing happens when the lid is
closed and the Vacuum and Seal
button or Instant Seal button is
pressed.
Make sure the lid is fully closed with the latch in the closed position
.
The Power light has gone out when
the lid is closed and the latch is in
the closed position.
If the appliance is left untouched for 12 minutes, it will enter Standby mode and all indicator lights will
remain off. Press the appropriate function button to return to the required mode (e.g. Vacuum and
Seal).
Installation of a plug
If the plug is not suitable for the socket outlets in your home, it can be
removed and replaced by a plug of the correct type. If you remove the
plug it must not be connected to a 13 amp socket and the plug must
be disposed of immediately.
NOTE: If the terminals in the plug are not marked or if you are unsure
or in doubt about the installation of the plug please contact a qualified
electrician.
If a 13A 3-pin plug is fitted, it must be an ASTA approved plug,
conforming to BS1363 standard. Replacement fuses must be BSI or
ASTA BS1362 approved.
The wires in the mains lead are coloured as such:
BROWN - LIVE
BLUE - NEUTRAL
Please note that the colour of these mains wires may not correspond
with the colour markings that identify the terminals in your plug.
The BROWN coloured wire must be connected to the terminal, which
is marked with the letter “L” or is coloured RED.
The BLUE coloured wire must be connected to the terminal, which is
marked with the letter “N” or is coloured BLACK.
DO NOT CONNECT either of these wires to the earth terminal in the
plug. The earth terminal plug is marked with the letter “E”, or with the
earth symbol , or coloured GREEN, or GREEN and YELLOW.
Do Not Connect
Mains Wires Here
Blue
(Neutral)
Brown
(Live)
3A
Fuse
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FoodSaver IFS005X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FoodSaver IFS005X in the language / languages: All languages as an attachment in your email.

The manual is 2.95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info