624376
27
Zoom out
Zoom in
Previous page
1/29
Next page
27
Inst/Line
Some of the channels on your interface may be able to accept electric instruments directly. Selecting
INST for these channels unbalances the input and alters the gain and impedance to optimise the
pre-amplifier for a high-impedance source like an electric guitar.
Selection of INST mode is confirmed by a red LED on the unit’s front panel.
The alternative switch position for these channels is LINE; in this mode, the inputs are suitable for a
standard balanced line level signal.
All the channels on your interface are able to accept dynamic or condenser microphones. The
Combo-type connectors sense either an XLR plug or a jack plug, and reconfigure the pre-amplifier
for mic or line operation automatically. The channels which additionally have the INST function use
the same connector.
Monitor Controls
It is very convenient (and traditional!) to adjust your master monitoring volume with a conventional
rotary control. Clarett interfaces have a MONITOR control on the front panel for this purpose.
Normally (i.e., by default), this will adjust the level at Monitor Outputs 1 and 2 while also providing
Mute and Dim control.
If you are using some of the Clarett’s other outputs for secondary speakers typically nearfield,
though also in LCR or surround setups – you can assign the rotary control, Mute and DIM switches
to affect them as well.
The options are:
1-2 – Monitor Outputs 1 & 2 (default setting)
1-4 – Monitor Outputs 1 & 2 and Line Outputs 3 & 4
1-6 – Monitor Outputs 1 & 2 and Line Outputs 3 to 6
All – Monitor Outputs 1 & 2 and Line Outputs 3 to 10
None The rotary control, MUTE and DIM switches are disabled; output levels may still be
controlled from the software faders.
Note: Assigning outputs 7-8 and 9-10 to monitor control will affect the level of the headphone outputs
as they are shared.
In the Output tabs on the Mixing & Routing page, the fader “knob” will be green for the outputs
assigned to the hardware rotary control. This means that the on-screen fader is inoperative and you
have to adjust the level of those outputs from the front panel. However, the on-screen fader position,
plus Mute and Dim status will reflect the hardware controls operation.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Focusrite Control at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Focusrite Control in the language / languages: English as an attachment in your email.

The manual is 5,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Focusrite Control

Focusrite Control User Manual - German - 29 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info