624402

Focusrite Control 2802 Manual

49
Zoom out
Zoom in
Previous page
1/55
Next page
Connector Wiring & Specications
Control 2802 Operating Manual 49
Master Section Connections
Working from top left to right:
Control 2802 connects to your DAW via IP-based networking
protocols, using the standard RJ-45 CAT-5e Ethernet port.
This provides bi-directional high speed communication to your
DAW, and carries MIDI automation data as well as control
surface protocols. There are two LEDs that indicate network
connection and activity.
The Main Speaker, Alt Speaker, Aux 1 & 2, Cue and Main
Mix outputs are on balanced male XLR connectors with <75
Ohms output impedance and a maximum output level of
+27dBu.
The DAW Mix, DAW F/B and External Stereo inputs are
on balanced female XLR connectors with >10k Ohms input
impedance and a maximum input level of +27dBu.
Two stereo FX Returns and the External Compressor
inputs are provided on balanced 1/4” TRS jack, with an input
impedance of >10k Ohms and a maximum input level of
+27dBu.
The External Compressor outputs are provided on balanced
1/4” TRS jack and have an output impedance of <75 Ohms with
a maximum output level of +27dBu.
The Main Mix Inserts are also on balanced 1/4” TRS jack with
the send jacks providing an output impedance of <75 Ohms and
a maximum drive capability of +21dBu, while the return jacks
offer >10k Ohms input impedance with +21dBu of maximum
input level.
The Mains Power input is a stand 3-pin IEC connector with
integrated fuse, it will accept line voltages from 100-240V
±10%. The fuse is a T2A slow-blow.
The Headphone output is an unbalanced, stereo TRS 1/4” jack
connection with enough current drive to cause hearing damage
if driven hard – BE CAREFUL, protect your ears!
The External Talkback microphone input is a balanced
female XLR connector with >5k Ohms input impedance and
a maximum input level of +7dBu. Please note 48V phantom
power can be provided to this input.
Unbalancing Control 2802
To unbalance a Control 2802 line level input, link pin 3 to pin
1 at the source. Please note that this must be achieved at the
source end. Therefore, the Control 2802 line input must be
left wired as balanced to preserve some of the common-mode
rejection performance (CMRR) of the input stage. Please refer
to the rst diagram at the bottom of the page.
To unbalance an output from Control 2802, link pin 3 to pin 1
at the output of the console.
Please note that this can also be achieved in a 1/4” TRS Jack
connector by connecting the ring to the sleeve within the jack
housing. To achieve an unbalanced output from the DB25
channel direct outputs, you will have to do it at the terminating
end, assuming that the cable breaks out into tails. Please refer
to the second diagram at the bottom of the page.
Please note that you should not leave as much exposed bare
shield as can be seen in these diagrams. They have been
exaggerated for clarity.
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Focusrite Control 2802 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Focusrite Control 2802 in the language / languages: English as an attachment in your email.

The manual is 31,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info