Husqvarna AB, 561 82, Huskvarna, Sweden
Declare under our sole responsibility that the product(s);
Category............................Electric Garden Shredder
Type(s) ............................PAS2200, PAS2500
Identification of Series.......See Product Rating Label
Year of Construction..........See Product Rating Label
Conforms to the essential requirements & provisions of the following EC Directives:
2006/42/EC, 2004/108/EC, 2000/14/EC
based on the following EU harmonized standards applied:
EN60335-1, prEN50434, EN13683, EN50366, EN55014-1, EN61000-3-2, EN61000-3-11
The maximum A weighted sound pressure level L
pA
at the operator’s position, recorded on a sample of the above
product(s) corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 20643 on a sample of the above
product(s) corresponds to the Value a
h
given in the table.
2000/14/EC: The Measured Sound Power L
WA
& Guaranteed Sound Power L
WA
values are according to the tabulated
figures.
Conformity Assessment Procedure......... Annex V
Notified Body........................................... Intertek, Cleeve Road
Leatherhead, Surrey
KT22 7SB, England
Newton Aycliffe 26/09/2011
M.Bowden
Global R & D Director - Walk behind
Keeper of technical documentation
EN 61000-3-11 Compliance statement
Depending on the characteristics of the local electricity supply network, use of this product may result in short voltage
drops at the instant of switching on. This may influence other electrical equipment e.g a momentary dimming of a
lamp. If the Mains impedance Zmax of your electricity supply is less than the value shown in the table (applicable to
your model) then these effects will not occur. The value of the network impedance may be determined by contacting
your electricity supply authority
Guarantee and Guarantee Policy
If any part is found to be defective due to faulty manufacture
within the guarantee period, Husqvarna UK Ltd., through its
Authorised Service Repairers will effect the repair or
replacement to the customer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken
apart or tampered with by any person not authorised by
Husqvarna UK Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way diminishes
the customers statutory rights.
Failures due to the following are not covered, therefore it is
important that you read the instructions contained in this
Operator's Manual and understand how to operate and
maintain your machine:
Failures not covered by guarantee
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in
accordance with the instructions and recommendations
contained in this Operator's Manual.
* Machines used for hire are not covered by this
guarantee.
* The following items listed are considered as wearing parts
and their life is dependent on regular maintenance and are,
therefore not normally subject to a valid warranty claim:
Blades, Electric Mains cable, Cutting Plate
* Caution!
Husqvarna UK Ltd. does not accept liability under the
warranty for defects caused in whole or part, directly or
indirectly by the fitting of replacement parts or additional
parts that are not either manufactured or approved by
Husqvarna UK Ltd., or by the machine having been
modified in any way.
ENGLISH - 3
Service Recomendations
• Your product is uniquely identified by a silver and black product rating label.
• We strongly recommend that your product is serviced at least every twelve months, more often in a professional application.
EC DECLARATION OF CONFORMITY
Type
Width of Cut (mm)
Speed of Rotation of Cutting Device (rpm)
Power (kW)
Measured Sound Power
L
WA
(dB(A))
Guaranteed Sound Power
L
WA
(dB(A))
Level L
pA
(dB(A))
Uncertainty K
pA
(dB(A))
Value
a
h
(m/s
2
)
Uncertainty K
ah
(m/s
2
)
Weight (Kg)
Mains Impedance Zmax (Ω)
PAS2200
35
40
2.2
97
98
85
2.5
2.40
1.5
31.3
0.340
PAS2500
40
40
2.5
97
98
85
2.5
2.40
1.5
32.5
0.314
