How to Mow
How to Mow
1. Start mowing the edge of the lawn nearest to the
power point so the cable is laid out on the lawn you
have already cut.
2. Mow twice a week during the growing season, your
l
awn will suffer if more than a third of its length is cut
at one time.
Do Not Overload Your Mower
Mowing long thick grass may cause the motor speed to
drop, you will hear a change in the motor sound. If the
motor speed drops you may overload your lawnmower
which may cause damage. When mowing in long thick
grass a first cut with the cutting height set higher will
help reduce the load. See Cutting Height Adjustment.
Edging Comb (R1)
Enables cutting up close to walls and fences
Caring for your Lawnmower
Cleaning
•
USE GLOVES
•
IMPORTANT
:- It is very important that you keep your
lawnmower clean. Grass clippings left in any of the
air intakes or under the deck could become a
potential fire hazard.
1. Remove grass from under the deck with brush.
(V1)
2. Using a soft brush - remove grass clippings from all
air intakes
(V2)
, the discharge chute
(V3)
and the
grass box
(V4)
.
3. Using a soft brush, remove grass clippings from the
vision window
(V5)
.
4. Wipe over the surface of your lawnmower with a dry
cloth
(V6)
.
•
IMPORTANT:-
Never use water for cleaning your
lawnmower, as this could damage the lawnmower and
invalidate the guarantee. Do not clean with
chemicals, including petrol, or solvents - some can
destroy critical plastic parts.
Storing your Cable
• Your electric cable can be wrapped around the hooks
to enable tidy and safe storage
(W1)
.
Storing your Lawnmower:
• Store in a dry place where your lawnmower is
protected from damage
• Loosen the wing knobs to enable the handles to be
folded over the product
(W2)
ensuring that the upper
handle is supported.
At the End of the Mowing Season
1. Replace bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Make sure that the electric cable is stored correctly to
prevent damage.
Fault Finding Hints
Fails to Operate
1. Is the correct Starting procedure being followed? See
‘To Start your Lawnmower’
2. Is the Power Turned On?
3. Check the fuse in the plug, if blown replace.
4. Fuse continues to blow?
Immediately disconnect from the mains electricity
supply and consult your Husqvarna Service Centre.
Poor Grass Collection
1. Disconnect from the mains electricity supply.
2. Clean the outside of the air intakes, the discharge
chute and the underside of the deck.
3. Raise to a higher height of cut. See Cutting Height
Adjustment.
4.
If poor collection persists.
Immediately disconnect from the mains electricity
supply and consult your Husqvarna Service Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Check that the blade is fitted correctly?
3. If the blade is damaged or worn, replace it with a new
one.
4. If vibration persists?
Immediately disconnect from the mains electricity
supply and consult your Husqvarna Service Centre.
Lawnmower becomes heavy to push
1. Disconnect from the mains electricity supply.
2. In long grass or uneven ground, the height of cut
should be raised to a higher position. See Cutting
Height Adjustment.
3. Check that the wheels can rotate freely.
4. If problem persists?
Immediately disconnect from the mains electricity
supply and consult your Husqvarna Service Centre.
Replacement Parts
Blade 34cm
Reference no.: FLY 066
Part no.: 577366490
Blade 37cm
Reference no.: FLY 067
Part no.: 579041990
Grassbox Full Window
• As the grassbox fills up, grass will be visible through
the window
(Q)
.
• When the window/grassbox is full it is time to empty
the grassbox.
ENGLISH - 3
Removing and Fitting the Blade
Switch off, wait until the blade has stopped rotating and
disconnect from the mains electricity supply BEFORE
attempting to remove or refit the blade.
Always handle the blade with care - sharp edges could
cause injury. USE GLOVES.
Removing the Blade
S1 - blade bolt S2 - washer S3 - blade
1. To remove the blade bolt, hold the blade firmly with a
gloved hand and with a spanner, loosen the blade bolt
by turning it anti-clockwise
(S)
.
2. Remove the blade bolt, washer and blade.
(S)
3. Inspect for damage and clean as necessary.
4. In the event of a blade becoming difficult to remove,
insert a screwdriver
(T1)
into the hole
(T2)
to lock the
drive, then use a spanner to loosen the blade bolt by
turning the spanner anti-clockwise. Ensure the
screwdriver is removed before atempting to turn on
the machine.
Renew your metal blade after 50 hours mowing or 2 years
whichever is the sooner - regardless of condition. If the
blade is cracked or damaged replace it with a new one.
Fitting the Blade
1. Fit the blade to the shaft with the sharp edges of the
blade pointing away from the shaft.
2. Re-assemble blade bolt through the washer and the
blade.
3. Hold the blade firmly with a gloved hand and tighten
the blade bolt firmly with a spanner . Do not over tighten.
5765592-02 Flymo Chevron 34VC-37VC Euro.qxp_???????-01 Visimo-Easimo Euro(Cleva) 08/01/2016 11:41 Page 10
