624064

Fluke networks TS23 PRO Manual

6
Zoom out
Zoom in
Previous page
1/22
Next page
2
TS23 PRO Test Set
Users Guide
Safety Information
The following IEC symbols are used either on the test
set or in the manual:
Warning
To avoid possible fire, electric shock, or
personal injury:
• Do not use the test set if it is damaged. Before you
use the test set, inspect the case. Look for cracks or
missing plastic. Pay particular attention to the
insulation surrounding the connectors.
• Do not use around explosive gases or vapors, or in
a damp or wet environment when hazardous
voltage is present.
• Do not connect the test set to lines that have more
than 140 V dc.
• The test set meets IEC Measurement Category I.
CAT I equipment is designed to protect against
transients in equipment on circuits not directly
connected to MAINS. Under no circumstances
should the test leads of the test set be connected
to any CAT II, CAT III, or CAT IV rated circuit.
• Do not use test leads if they are damaged. Examine
the test leads for exposed metal and damage to
the insulation. Make sure the wear indicator on the
cords does not show. The wear indicator is the
white layer below the outer, braided layer. Verify
the continuity of the test leads. To replace the test
leads, see page 15.
• Do not use the test set with the case open.
• Do not use the test set if it operates incorrectly.
• Do not connect the test set to voltages higher than
the maximum specified by the Measurement
Category (CAT) rating of the lowest-rated
individual component of the test set, test leads, or
accessory.
• Use only a 9 V battery, correctly installed, to supply
power to the test set.
• Use only accessories that are approved by Fluke
Networks.
• Do not touch the exposed metal of the test clips.
• If this product is used in a manner not specified by
the manufacturer, the protection provided by the
product may be impaired.
• To prevent unreliable test results, replace the
battery as soon as the BATTERY LED flashes.
• Before you remove the battery door, disconnect
the test leads from the line.
Warning: Risk of personal injury. See the
manual for details.
Caution: Risk of damage or destruction to
equipment or software. See the manual
for details.
Warning: Risk of electric shock.
Conforms to relevant Australian EMC
requirements.
Conforms to relevant Canadian and US
standards.
Conforms to European Union directives.
Double Insulated - does not require
connection to earth ground.
Do not put products containing circuit
boards into the garbage. Dispose of circuit
boards in accordance with local
regulations.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke networks TS23 PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke networks TS23 PRO in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info