763940
94
Zoom out
Zoom in
Previous page
1/100
Next page
8808A
Users Manual
A-4
Table A-2. Sample Dual Display Applications (cont.)
Primary
Display
Secondary
Display
Applications
REL Resistance Select and sort resistors. (See also "Using the Compare Function"
in Chapter 3.)
HOLD Actual Value Show actual measurement while holding a previous, stable
measurement on the primary display
8808A
5-1/2 DIGIT MULTIMETER
HI
LO
1000V
750V
2W/4W
MAX
INPUT SENSE
HI
LO
4
W
10 A
mA
200 mA
MAX 10 A
MAX
1000V CAT I
600 V CAT II
500 V pk
V
1V
300V
eue27.eps
Figure A-2. DC Voltage and DC Current Measurement on Input Signal
The lead from the internal measuring circuitry of the meter to the LO terminal (on the
front panel) is the same for both voltage and current measurements. The resistance of this
lead is approximately .003 ohm. If current is being measured, therefore, a voltage drop
will occur in the resistance that is common to both circuits. This internal resistance, when
added to the external resistance of the lead from the COM input terminal will affect the
accuracy of the voltage reading. For instance, if the external lead resistance is .007 ohm,
the "total" common resistance is .010 ohm. If there is 1 A of current, the voltage reading
would be affected by:
(1 A x.01ohm ) = .01 V or 10 m V.
Depending on the circumstances, this may be significant.
If you want to measure dc voltage on an input signal in the primary display and dc
current in the secondary display, proceed as follows:
1. Turn the Meter on.
2. Press D to select the dc voltage function for the primary display.
3. Press Q then E to select the dc current function for the secondary display.
4. Connect the leads to the test circuit as shown in Figure A-2 and read the
measurements on the display. Although current will be displayed as negative, it is in
fact positive when interpreted according to current flow convention.
Response Times
Response time is the time between a change in an input and when that change is
displayed. The meter’s response time depends on many factors: the measurement
94


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke 8808A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke 8808A in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fluke 8808A

Fluke 8808A User Manual - German - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info