764336
115
Zoom out
Zoom in
Previous page
1/130
Next page
July 2011 Rev. 1, 8/12
© 2011-2012 Fluke Corporation. All rights reserved. Specifications are subject to change without notice.
All product names are trademarks of their respective companies.
753/754
Documenting Process Calibrator
Users Manual
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship for three years from the date of purchase. This
warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or
abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf.
To obtain service during the warranty period, contact your nearest Fluke authorized service center to obtain return
authorization information, then send the product to that Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries
do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of
liability may not apply to you.
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99
i
Table of Contents
Title Page
Introduction .................................................................................................................... 1
How to Contact Fluke ..................................................................................................... 1
Safety Information .......................................................................................................... 2
Standard Equipment....................................................................................................... 6
Functions ........................................................................................................................ 9
Get Started ..................................................................................................................... 11
Operation Features ........................................................................................................ 13
Input and Output Jacks .............................................................................................. 13
Buttons ...................................................................................................................... 15
Display ....................................................................................................................... 18
Strap and Stand......................................................................................................... 21
The Battery ..................................................................................................................... 22
Charge the Battery .................................................................................................... 22
Battery Charge Level ................................................................................................. 23
Battery Life ................................................................................................................ 23
753/754
Users Manual
ii
Preserve Battery Life ................................................................................................ 25
The Battery Charger ................................................................................................. 25
Display Languages ........................................................................................................ 26
Display Intensity............................................................................................................. 26
Date and Time ............................................................................................................... 26
The Backlight ................................................................................................................. 28
Personalize the Product ................................................................................................. 28
Measure Mode ............................................................................................................... 29
Measurement Ranges ............................................................................................... 29
Electrical Parameter Measurement ........................................................................... 30
Continuity Test .......................................................................................................... 32
Pressure Measurement ............................................................................................. 32
Temperature Measurement ...................................................................................... 36
Thermocouple Use ............................................................................................... 36
Resistance-Temperature Detectors (RTDs) ......................................................... 39
Measurement Scale .................................................................................................. 43
Linear-Output Transmitters .................................................................................. 43
Square-Law Process Variables ............................................................................ 43
Measure or Source with Custom Units ...................................................................... 44
Using the 700-IV Current Shunt ................................................................................ 44
Damping Measurements ........................................................................................... 45
Source Mode ................................................................................................................. 45
Source Electrical Parameters ................................................................................... 45
4 to 20 mA Transmitter Simulation ............................................................................ 48
Supply Loop Power ................................................................................................... 50
Source Pressure ....................................................................................................... 52
Thermocouple Simulation ......................................................................................... 55
RTD Simulation ......................................................................................................... 56
Source Temperature with a Hart Scientific Drywell ................................................... 59
Contents (continued)
iii
Source Scale ............................................................................................................. 61
Linear-Responding Transmitters ........................................................................... 61
Square-Root Process Variables ............................................................................ 61
Step and Ramp the Output Value .............................................................................. 62
Manual Step Use .................................................................................................. 62
Auto Step Use ....................................................................................................... 62
Ramp the Output .................................................................................................. 63
Simultaneous Measure/Source ...................................................................................... 66
Process Instrument Calibration ...................................................................................... 69
Generate “As Found” Test Data ................................................................................ 69
Transmitter Adjustment ............................................................................................. 74
“As Left” Test Run ..................................................................................................... 75
Test Comments ......................................................................................................... 75
Calibrate a Delta-Pressure Flow Instrument .............................................................. 75
Switch Calibration ...................................................................................................... 76
Transmitter Mode ........................................................................................................... 79
Memory Operations ........................................................................................................ 80
Save Results ............................................................................................................. 80
Review the Memory ................................................................................................... 83
Log Data .................................................................................................................... 83
Record Min and Max Measurements ......................................................................... 86
Run a Preloaded Task ............................................................................................... 87
Clear the Memory ...................................................................................................... 87
The Calculator ................................................................................................................ 87
Save to and Recall from the Registers ...................................................................... 88
Use the Calculator to Set the Source Value .............................................................. 88
Quick Guide to Applications ........................................................................................... 88
Communication with a PC .............................................................................................. 101
Maintenance ................................................................................................................... 101
753/754
Users Manual
iv
Battery Replacement ................................................................................................ 101
Clean the Product ..................................................................................................... 101
Calibration Data ........................................................................................................ 102
In Case of Difficulty ................................................................................................... 102
Service Center Calibration or Repair ........................................................................ 102
User-Replaceable Parts ................................................................................................. 102
Accessories ................................................................................................................... 104
Specifications ................................................................................................................ 106
General Specifications ................................................................................................... 106
Environmental Specifications .................................................................................... 106
Standards and Agency Approval Specifications........................................................ 106
Detailed Specifications .................................................................................................. 107
DC mV Measurement ............................................................................................... 107
DC Voltage Measurement ......................................................................................... 108
AC Voltage Measurement ......................................................................................... 108
DC Current Measurement ......................................................................................... 109
Resistance Measurement ......................................................................................... 109
Continuity Testing ..................................................................................................... 109
Frequency Measurement .......................................................................................... 110
±DC Voltage Output .................................................................................................. 110
+DC Current Source ................................................................................................. 111
+DC Current Simulate (External Loop Power) .......................................................... 111
Resistance Sourcing ................................................................................................. 111
Frequency Sourcing .................................................................................................. 112
Temperature, Thermocouples ................................................................................... 113
Temperature, Resistance Temperature Detectors .................................................... 116
Loop Power ............................................................................................................... 117
v
List of Tables
Table Title Page
1. Symbols ................................................................................................................................. 4
2. Summary of Source and Measure Functions ........................................................................ 10
3. Input/Output Jacks and Connectors ...................................................................................... 13
4. Buttons .................................................................................................................................. 16
5. Elements of a Typical Display ............................................................................................... 20
6. Typical Battery Life ................................................................................................................ 23
7. Thermocouple Types Accepted ............................................................................................. 37
8. RTD Types Accepted ............................................................................................................ 39
9. Simultaneous MEASURE/SOURCE Functions with Loop Power Disabled ........................... 67
10. Simultaneous MEASURE/SOURCE Functions with Loop Power Enabled ............................ 68
11. Duration Limits ...................................................................................................................... 84
12. Replacement Parts ................................................................................................................ 103
753/754
Users Manual
vi
vii
List of Figures
Figure Title Page
1. Standard Equipment .............................................................................................................. 7
2. Jumper Connections ............................................................................................................. 12
3. Measure/Source Example ..................................................................................................... 12
4. Input/Output Jacks and Connectors ...................................................................................... 14
5. Buttons .................................................................................................................................. 15
6. Elements of a Typical Display ............................................................................................... 19
7. Stand Use and Strap Attachment .......................................................................................... 21
8. Battery Removal and Charger Use ........................................................................................ 24
9. Time and Date Display .......................................................................................................... 27
10. Edit the Date Format ............................................................................................................. 27
11. Personalize the Product ........................................................................................................ 28
12. Electrical Measurement Connections .................................................................................... 31
13. Gage and Differential Pressure Modules ............................................................................... 33
14. Pressure Measurement Connections .................................................................................... 35
15. Temperature Measurement with a Thermocouple ................................................................. 38
753/754
Users Manual
viii
16. Correct Jumper Use .............................................................................................................. 41
17. Temperature Measurement with an RTD .............................................................................. 42
18. Electrical Source Connections .............................................................................................. 47
19. Connections fo Simulate a 4 to 20 mA Transmitter ............................................................... 49
20. Connections to Supply Loop Power ...................................................................................... 51
21. Connections to Source Pressure .......................................................................................... 54
22. Connections to Simulate a Thermocouple ............................................................................ 57
23. Connections to Simulate an RTD .......................................................................................... 58
24. Source Temperature with Drywell ......................................................................................... 60
25. Ramp Screen ........................................................................................................................ 64
26. Check a Relay Output Trip Alarm ......................................................................................... 65
27. Measure and Source Screen ................................................................................................ 66
28. Process Instrument Calibration Screen................................................................................. 70
29. Process Instrument Calibration Screen 2 .............................................................................. 70
30. Calibrate a Thermocouple Temperature Transmitter ............................................................ 71
31. Calibration Parameters Screen ............................................................................................. 72
32. Measure and Source Screen for Calibration ......................................................................... 73
33. Error Summary Screen ......................................................................................................... 73
34. As Left Data Screen .............................................................................................................. 75
35. Switch Terminology .............................................................................................................. 76
36. Saved Data Screen ............................................................................................................... 81
37. Additional Data Input Screen ................................................................................................ 81
38. Alphanumeric Entry Window ................................................................................................. 82
39. Memory Review Screen ........................................................................................................ 83
40. Data Log Parameters Screen ............................................................................................... 83
41. Start Logging Screen ............................................................................................................ 85
42. Min Max Screen .................................................................................................................... 86
43. Chart Recorder Calibration ................................................................................................... 89
44. Voltage Drop Measurement .................................................................................................. 89
Contents (continued)
ix
45. Monitor AC Line Voltage and Frequency ............................................................................... 90
46. Current-to-Pressure (I/P) Transmitter Calibration .................................................................. 91
47. Output Current of a Transmitter Measurement ...................................................................... 92
48. Precision Resistor Measurement ........................................................................................... 93
49. Resistance Source ................................................................................................................ 93
50. Checking a Switch ................................................................................................................. 94
51. Tachometer Examination ....................................................................................................... 94
52. Analog and HART Pressure Transmitter Connection ............................................................ 95
53. mV to Current Transmitter Calibration ................................................................................... 96
54. Vortex Sheding Flowmeter Check ......................................................................................... 97
55. HART and Analog RTD Transmitter Connections ................................................................. 98
56. Analog and HART Thermocouple Transmitter Connections .................................................. 99
57. Transmitter HART- Comm Only ............................................................................................ 100
753/754
Users Manual
x
1
Introduction
The 753 and 754 Documenting Process Calibrators (the
Product) are battery-powered, hand-held instruments that
measure and source electrical and physical parameters. In
addition, the 754 supplies basic HART communicator
functions when used with HART-capable transmitters. See
the 754 HART Mode Users Guide for instructions on how to
use the HART communication feature.
The Product helps troubleshoot, calibrate, verify, and
document work performed on process instruments.
Note
All figures in this manual show the 754.
How to Contact Fluke
To contact Fluke, call one of the following telephone
numbers:
Technical Support USA: 1-800-44-FLUKE
(1-800-443-5853)
Calibration/Repair USA: 1-888-99-FLUKE
(1-888-993-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Europe: +31 402-675-200
Japan: +81-3-6714-3114
Singapore: +65-6799-5566
Anywhere in the world: +1-425-446-5500
Or, visit Fluke's website at www.fluke.com.
To register your product, visit http://register.fluke.com.
To view, print, or download the latest manual supplement,
visit http://us.fluke.com/usen/support/manuals.
The latest software trial version of DPCTrack2 can be
downloaded at www.fluke.com/DPCTrack. For more
information see “Communication with a PC”.
753/754 Accessories can be found at
www.fluke.com/process_acc.
753/754
Users Manual
2
Safety Information
A Warning identifies conditions and actions that pose
hazards to the user; a Caution identifies conditions and
actions that may damage the Product or the equipment
under test.
 Warning
To prevent personal injury, use the Product
only as specified, or the protection supplied by
the Product can be compromised.
To prevent possible electrical shock, fire, or
personal injury:
Read all safety Information before you use
the Product.
Carefully read all instructions.
Use only correct measurement category
(CAT), voltage, and amperage rated
probes, test leads, and adapters for the
measurement.
The battery must be locked in place before
you operate the Product.
Recharge the battery when the low battery
indicator shows to prevent incorrect
measurements.
Do not apply more than the rated voltage,
between the terminals or between each
terminal and earth ground.
Limit operation to the specified
measurement category, voltage, or
amperage ratings.
Do not exceed the Measurement Category
(CAT) rating of the lowest rated individual
component of a Product, probe, or
accessory.
Measure a known voltage first to make
sure that the Product operates correctly.
Do not touch voltages > 30 V ac rms, 42 V
ac peak, or 60 V dc.
Do not use the Product around explosive
gas, vapor, or in damp or wet
environments.
Do not use and disable the Product if it is
damaged.
Do not use the Product if it operates
incorrectly.
Keep fingers behind the finger guards on
the probes.
Remove all probes, test leads, and
accessories that are not necessary for the
measurement.
Only use probes, test leads, and
accessories that have the same
measurement category, voltage, and
amperage ratings as the Product.
Documenting Process Calibrators
Safety Information
3
Connect the common test lead before the
live test lead and remove the live test lead
before the common test lead.
Use only current probes, test leads, and
adapters supplied with the Product.
Do not touch the probes to a voltage
source when the test leads are connected
to the current terminals.
Use only cables with correct voltage
ratings.
Do not use test leads if they are damaged.
Examine the test leads for damaged
insulation, exposed metal, or if the wear
indicator shows. Check test lead
continuity.
Examine the case before you use the
Product. Look for cracks or missing
plastic. Carefully look at the insulation
around the terminals.
Always put the stackable end of the test
lead into a terminal of the Product.
753/754
Users Manual
4
Symbols used on the Product and in this manual are explained in Table 1.
Table 1. Symbols
Symbol Meaning Symbol Meaning
Earth ground Common (LO) Input equipotentiality
AC- alternating current Conforms to relevant North American Safety
Standards.
DC- direct current Conforms to European Union directives.
Risk of danger. Important information.
See manual. Pressure
Hazardous voltage. Risk of electrical
shock.
This product complies with the WEEE Directive
(2002/96/EC) marking requirements. The affixed
label indicates that you must not discard this
electrical/electronic product in domestic
household waste. Product Category: With
reference to the equipment types in the WEEE
Directive Annex I, this product is classed as
category 9 "Monitoring and Control
Instrumentation” product. Do not dispose of this
product as unsorted municipal waste. Go to
Fluke’s website for recycling information.
Documenting Process Calibrators
Safety Information
5
Table 1. Symbols (cont.)
Symbol Meaning Symbol Meaning
Application around and removal from
HAZARDOUS LIVE conductors is
permitted. Conforms to relevant Australian standards.
Double insulated German certifying body.
CAT II CAT II equipment is designed to protect against transients from energy-consuming equipment supplied from
the fixed installation, such as TVs, PCs, portable tools, and other household appliances.
753/754
Users Manual
6
Standard Equipment
Items included with the Product are listed below and
shown in Figure 1. If the Product is damaged or
something is missing, contact the place of purchase
immediately.
Battery with integrated charger/power supply and
international adapters
Printed multilingual 753/754 Getting Started Manual
753/754 Manual CD containing multilingual Users
Manuals
Three sets of TP220-1 test probes
Three sets of 75X industrial test leads with stackable
ends
Three pairs of 754 Alligator Clip Set (extended tooth)
Two sets of AC280 Suregrip Hook Clips (red and
black)
Adjustable quick-release strap
Jumper for three-wire RTD measurement
connections
USB Cable: 6 ft. type A to type mini-B
HART communications cable (754)
Calibration Manual (available from Fluke’s website)
Sample DPCTrack2 application software
NIST-traceable Certificate of Calibration
TC Input Cap
Documenting Process Calibrator
Standard Equipment
7
Fluke-75X-Stackable
Test Lead Set (3 Red and 3 Black)
Jumper
TC Cap
TP220-1
Test Probe
(3 Red and 3 Black)
Strap
754-8016,
Alligator Clip Set
(3 Red and 3 Black)
AC280 SureGrip
TM
Hook Clip Set
(2 Red and 2 Black)
gks01f.eps
Figure 1. Standard Equipment
753/754
Users Manual
8
753/754 Getting
Started
753/754 Manuals
CD
DPCTrack2
CD
Lithium Ion
Battery Pack
USB Cable
HART
Communication
Cable
Battery Charger/Universal Power Supply
gks02f.eps
Figure 1. Standard Equipment (cont)
Documenting Process Calibrator
Functions
9
Functions
A summary of functions supplied by the Product is shown in
Table 2. More features include:
Analog display for easy to read measurements when
inputs are unstable.
Localized display (5 languages). See “Display
Languages”.
Thermocouple (TC) input/output jack and internal
isothermal block with automatic reference-junction
temperature compensation. Or manually record an
external temperature reference.
Test results storage.
Data logging. Automatically log up to 8,000 data points.
A USB computer interface to upload or download tasks,
lists, and results.
Automatic calibration procedures for transmitters and
limit switches when you use split screen
MEASURE/SOURCE mode.
Transmitter mode in which the Product can be
configured to emulate the functions of a process
instrument.
Calculator feature with square-root function, and
accessible registers that contain measure and source
values.
Damp feature (smoothes the last several readings),
with display indicator of damped status.
Display of measurements in engineering units, percent
of scale, square-law inputs, or custom units.
Min/Max feature captures and shows minimum and
maximum measured levels.
Set source values to engineering units, percent of
scale, square-law outputs, or custom units.
Manual and automatic stepping and an output ramp
feature for testing limit switches. Trip detect is either a 1
V change or a continuity status change (Open or Short)
from one ramp increment to the next.
For performance testing and calibration instructions,
download the 753/754 Calibration Manual from Fluke’s
website.
753/754
Users Manual
10
Table 2. Summary of Source and Measure Functions
Function Measure Source
Volts dc 0 V to ±300 V 0 V to ±15 V (10 mA max)
h Volts ac 0.27 V to 300 V rms, 40 Hz to 500 Hz No sourcing
h Frequency 1 Hz to 50 kHz
0.1 V to 30 V p-p sine wave, or 15 V peak
square wave, 0.1 Hz to 50 kHz sine wave,
0.01 Hz square wave
q Resistance 0 Ω to 10 kΩ 0 Ω to 10 kΩ
dc Current 0 mA to 100 mA 0 to 22 mA sourcing or sinking
q Continuity Beep and the word Short indicates
continuity
No sourcing
t Thermocouple Types E, N, J, K, T, B, R, S, C, L,U, BP, or XK
t RTD
(2-W, 3-W, 4-W)
100 Ω Platinum (3926)
100 Ω Platinum (385)
120 Ω Nickel (672)
200 Ω Platinum (385)
500 Ω Platinum (385)
1000 Ω Platinum (385)
10 Ω Copper (427)
100 Ω Platinum (3916)
p Pressure
[1] 29 modules ranging from 0 to 1 inch H2O
(250 Pa) to 0 to 10,000 psi (69,000 kPa)
s Loop Power 26 V
[1] Use an external hand pump or other pressure source as a pressure stimulus for the source pressure function.
753/754
Users Manual
12
gks03f.eps
Figure 2. Jumper Connections
gks04s.bmp
Figure 3. Measure/Source Example
Documenting Process Calibrator
Operation Features
13
Operation Features
Input and Output Jacks
Figure 4 shows the input and output jacks and connectors.
Table 3 explains their use.
Table 3. Input/Output Jacks and Connectors
No. Name Description
HART jack (754 only) Connects the Product to HART devices.
Pressure module
connector Connects the Product to a pressure module.
TC input/output
Jack to measure or simulate thermocouples. This jack accepts a miniature
polarized thermocouple plug with flat, in-line blades spaced 7.9 mm (0.312 in)
center to center.
, MEASURE V jacks Input jacks to measure voltage, frequency, or three- or four-wire RTDs
(Resistance Temperature Detectors).
,
SOURCE mA,
MEASURE mA Ω RTD
jacks
Jacks to source or measure current, measure resistance and RTDs, and supply
loop power.
, SOURCE V Ω RTD
jacks Output jacks to source voltage, resistance, frequency, and to simulate RTDs.
Battery Charger jack
Jack for the battery charger/universal power supply (referred to as the battery
charger throughout this manual). Use the battery charger for bench-top
applications where ac line power is available.
USB port (Type 2) Connects the Product to a USB port on a PC.
753/754
Users Manual
14
754
DOCUMENTING PROCESS CALIBRATOR
P1
HART
15V
DC
1
2
4
5
69 7
3
8
11
10
gks05f.eps
Figure 4. Input/Output Jacks and Connectors
Documenting Process Calibrator
Operation Features
15
Buttons
Figure 5 shows the Product buttons and Table 4 tells their
functions. The softkeys are the four (F1-F4) blue buttons
below the display. Softkey functions are defined by the
labels that show above the softkey during operation. Softkey
labels and other display text are shown in this manual in
bold type, for example, Choices.
754
DOCUMENTING PROCESS CALIBRATOR
1
16
2
9
11
12
14 13
10
15
45
3
6
7
8
gks06f.eps
Figure 5. Buttons
753/754
Users Manual
16
Table 4. Buttons
Item Button Description
o Turns the Product on and off.
Selects mA (current) measure or source function. For loop power on/off, go to the Setup
mode.
Selects the dc voltage function in MEASURE mode, or selects dc voltage in SOURCE mode.
t Selects TC (thermocouple) or RTD (resistance temperature detector) measurement or
sourcing functions.
p Selects the pressure measurement or source function.
W
X
Y
Z
Softkeys. Does the function specified by the label above each softkey on the display.
Adjusts the backlight intensity (three levels).
s Enters and exits Setup mode to change operating parameters.
r (754)
(753)
(754) Toggles between HART communication mode and analog operation. In calculator
mode, this key supplies the square root function.
(753) Adjusts the Range of the Product.
Documenting Process Calibrator
Operation Features
17
Table 4. Buttons (cont)
Item Button Description
, , ,
Push or to increase display intensity. Push or to decrease intensity (seven levels).
Make choices from lists on the display.
Increase or decrease the source level when using the step feature.
In calculator mode, provides arithmetic functions (+ - ÷ ×).
Clears a partial data entry, or prompts for output value when in the SOURCE mode. When
you use a pressure module, zeros the pressure module indication.
Completes a numeric entry when a source value is set, or confirms a choice in a list. In
calculator mode, acts as the equals arithmetic operator (=).
q Toggles between resistance and continuity functions in MEASURE mode, or selects the
resistance function in SOURCE mode.
h Toggles between ac voltage and frequency functions in MEASURE mode, or selects
frequency output in SOURCE mode.
Numeric
keypad Used when a numeric entry is necessary.
Cycles the Product through MEASURE, SOURCE, and MEASURE/SOURCE modes.
753/754
Users Manual
18
Display
Figure 6 and Table 5 show a typical display. The display
shown is MEASURE mode. Near the top of the display is
Source Off.” This display area shows what is happening in
the other mode (SOURCE or MEASURE). The other parts
of the display are:
Status Bar: Shows the time and date, and the status of
Loop Power, Auto Battery Save, and Backlight Timeout;
all of which are set in Setup mode. The selected HART
channel (if HART is active-754 only) and low-battery
and backlight-on symbols are also show here.
Mode Indicator: Shows if the Product is in MEASURE
or SOURCE mode. In split screen
MEASURE/SOURCE mode, there is a Mode Indicator
for each window.
Measured Value: Shows the measured value in a
selection of engineering units or percent of scale.
Range Status: Shows if Auto Range is on, and what
range is currently in operation.
Custom Units Indicator: Shows that the displayed
units are custom. The initial engineering units of the
measure or source function are not shown.
Secondary Value: Shows the measure or source value
in initial engineering units when scaling or custom units
are on.
Documenting Process Calibrator
Operation Features
19
1
12
11
2 3 4 5
6
7
8
9
10
13
gks07c.eps
Figure 6. Elements of a Typical Display
753/754
Users Manual
20
Table 5. Elements of a Typical Display
Item Description
Time and Date Display
HART Indicator
Loop Power Indicator
Battery Gauge
Backlight Indicator
Source Status
Undamped (Unsettled) Indicator
Custom Units Indicator
Secondary Value
Softkey Labels
Measured Value
Mode Indicator
Status bar
Documenting Process Calibrator
Operation Features
21
Strap and Stand
After you unpack the Product, attach its carrying strap as shown in Figure 7. The straps can be adjusted as necessary to
hang the Product on any sturdy support. Figure 7 also shows how to open the Stand to put the Product at an optimal sight
angle for bench top use.
gks8f.eps
Figure 7. Stand Use and Strap Attachment
753/754
Users Manual
22
The Battery
Caution
For safe operation and maintenance of the
product:
Do not keep cells or batteries in a
container where the terminals can be
shorted.
Repair the Product before use if the battery
leaks.
Remove battery to prevent battery leakage
and damage to the Product if it is not used
for an extended period.
Connect the battery charger to the mains
power outlet before the Product.
Use only Fluke approved power adapters
to charge the battery.
Keep cells and battery packs clean and
dry. Clean dirty connectors with a dry,
clean cloth.
Do not short the battery terminals together.
Warning
To prevent personal injury:
Do not put battery cells and battery packs
near heat or fire. Do not put in sunlight.
Do not disassemble or crush battery cells
and battery packs.
Do not disassemble the battery.
Batteries contain hazardous chemicals that
can cause burns or explode. If exposure to
chemicals occurs, clean with water and get
medical aid.
Charge the Battery
Before you use the Product for the first time, charge its
battery.
To charge the battery while it is inside the Product:
1. Turn the Product OFF.
2. Connect the battery charger to the Product and keep it
OFF. The battery will not charge if the Product is on.
The battery fully charges in 8 hours while inside the Product.
See Figure 8.
To charge the battery while it is outside of the Product:
1. Turn the Product face down.
2. Use a flat-head screwdriver and move the battery lock
from (locked) to (unlocked).
Documenting Process Calibrator
The Battery
23
3. Remove the battery.
4. Connect the battery charger to the input. Outside of the
Product, the battery will charge in 5 hours.
Note
An optional 12-Volt car charger is available. See
“Accessories”.
Battery Charge Level
Use these two methods to make sure the Battery is
charged:
See the Battery Gauge Bar Graph on the display.
See the Battery Charge Indicator on the battery.
The Battery Charge Indicator can be seen while the battery
is outside of the Product. With the battery removed and not
connected to its charger, push the button below the Battery
Charge Indicator. Solid Green LEDs show the level of
charge on the battery. The Battery is fully charged when all
LEDs are illuminated.
Connect the battery charger to the battery and push the
button below the Battery Charge Indicator. LEDs flash to
show the charge level but also show that the battery is being
recharged. As the battery charges, the LED flashes and
moves to the top of the charge indicator.
Battery Life
The battery gauge bar graph is shown on the upper
right of the display.
Table 6 shows the typical operation time for a new, fully-
charged battery. Product performance is guaranteed to its
specification until the battery gage reads empty ().
To replace the battery, see “Battery Replacement”.
Table 6. Typical Battery Life
Operation Modes Backlight
Low Backlight
High
Measure, continuous 13 Hours 12 Hours
Measure and source, with
loop power on, continuous
7 Hours 6 Hours
Typical intermittent
operation
>16 Hours >16 Hours
753/754
Users Manual
24
gks9f.eps
Figure 8. Battery Removal and Charger Use
Documenting Process Calibrator
The Battery
25
Preserve Battery Life
An optional Auto Battery Save feature turns the Product off
after a selected set idle time. The default setting for Auto
Battery Save is Off. The setting is kept after the Product
power is off. Auto Battery Save operates the same when the
battery charger is used.
To turn on the Auto Battery Save feature:
1. Push s.
2. Push to highlight Off that follows Auto Battery
Save.
3. Push or the Choices softkey.
4. Push to highlight On, then push .
5. To use the timeout period shown on the display, stop
here. Push the Done softkey to exit Setup mode and do
not go on to step 6.
6. If you wish to change the timeout period, push to
select the timeout period following Battery Save
Timeout.
7. Push or the Choices softkey.
8. Record choice of timeout period in minutes (accepted
range: 1 to 120 minutes).
9. Push the Done softkey.
10. Push the Done softkey or s to exit Setup mode.
The Battery Charger
Caution
To avoid damage to the Product, use only the
Battery that comes with the Product, Fluke
model BP7240, part number 4022220.
Where ac power is available, the battery charger can be
used to conserve battery power and energize the Product.
When the battery is in the Product, the battery charges only
when the Product is off. When you calibrate an instrument,
best results come from battery power use.
An optional 12-V car adapter is available that can be used
to charge the battery outside of the Product. See
“Accessories”.
753/754
Users Manual
26
Display Languages
The Product shows information in five languages:
English
European French
Italian
German
Spanish
To change the display language:
1. Push s.
2. Push Y twice.
3. Push three times.
4. Push .
5. Push or to highlight the language choice.
6. Push to confirm the language choice. This
language is the power-up default.
7. Push s to exit Setup mode.
Display Intensity
There are two ways to increase display intensity:
Push . There are three levels of intensity when using
this button.
Push or to increase display intensity. Push or
to decrease intensity. There are six levels of intensity
when these buttons are used.
In calculator mode, all four direction keys are used for
arithmetic functions.
Date and Time
The date and time can be shown at the top of the display
during normal operation. The date and time can be turned
on or off in Setup mode. Date and time formats can also be
controlled. If you choose to not use the date and time
display, the calendar and clock must be set since a
timestamp is applied to all kept results.
Documenting Process Calibrator
Date and Time
27
To set the time and date displays:
1. Push s.
2. Push the Next Page softkey. See Figure 9.
gks38s.bmp
Figure 9. Time and Date Display
3. Push and to move the cursor to the necessary
parameter, then push or the Choices softkey to
choose a setting for that parameter.
For example, the display in Figure 10 is shown after
you select Date Format.
gks39s.bmp
Figure 10. Edit the Date Format
4. Push or to move the cursor to the necessary date
format.
5. Push to select the format and go back to Setup
mode.
6. Choose a different selection or push the Done softkey
or s to save the settings and exit Setup mode.
753/754
Users Manual
28
The Backlight
Push to change the backlight intensity from dim to bright
and back again. shows at the top of the display when the
backlight is active. Set the Product to turn the backlight off
automatically to keep battery use to minimum. When the
backlight is on and Auto Backlight Off is in operation, a is
shown at the top of the display.
To automatically dim the backlight after a set time:
1. Push s.
2. Push to move the cursor to the same line
as Auto Backlight Off.
3. Push or the Choices softkey.
4. Push to highlight On, then push .
5. To use the timeout period shown on the display, stop
here. Push the Done softkey to exit Setup mode and do
not go on to step 6.
6. To change the timeout period, push to highlight the
timeout period following Backlight Timeout.
7. Push or the Choices softkey.
8. Record the choice of timeout period in minutes
(accepted range: 1 to 120 minutes).
9. Push the Done softkey.
10. Push the Done softkey or s to exit Setup mode.
When the backlight dims, the Product also beeps.
Personalize the Product
Alphanumeric identifiers can be put into the Product to be
shown at power-up and in results that you keep. To install
an identifier:
1. Push s.
2. Push Next Page twice.
3. Push to move the cursor to the same line as ID.
4. Push or the Choices softkey. The screen in
Figure 11 is shown.
gks40s.bmp
Figure 11. Personalize the Product
753/754
Users Manual
30
Electrical Parameter Measurement
When the Product is turned on, it is in the dc voltage
measurement function. Figure 12 shows electrical
measurement connections. To select an electrical
measurement function from SOURCE or
MEASURE/SOURCE mode, first push for MEASURE
mode:
1. Push for current, for dc voltage, h once for ac
voltage or twice for frequency, or q for resistance.
Note
When you measure frequency, the Product tells
you to select a frequency range. If the measured
frequency is expected to be below 20 Hz, push
to select the lower frequency range, and then push
.
2. Connect the test leads for your measurement function
as shown in Figure 12.
Documenting Process Calibrator
Measure Mode
31
+–
gks10f.eps
Figure 12. Electrical Measurement Connections
753/754
Users Manual
38
Warning
30 V maximum to
TC Miniplug
Process Temperature
gks12f.eps
Figure 15. Temperature Measurement with a Thermocouple
Documenting Process Calibrator
Measure Mode
39
Resistance-Temperature Detectors (RTDs)
The Product accepts RTD types shown in Table 8. RTDs are characterized by their resistance at 0 °C (32 °F), which is called
the “ice point” or R0. The most common R0 is 100 Ω. A large number of RTDs come in a three-terminal configuration. The
Product accepts RTD measurement inputs in two-, three-, or four-wire connections. See Figure 17. A four-wire configuration
gives the highest measurement precision, and two-wire gives the lowest measurement precision.
Table 8. RTD Types Accepted
RTD Type Ice Point (R0) Material α Range (°C)
Pt100 (3926) 100 Ω Platinum 0.003926 Ω/Ω/°C -200 to 630
Pt100 (385) [1] 100 Ω Platinum 0.00385 Ω/Ω/°C -200 to 800
Ni120 (672) 120 Ω Nickel 0.00672 Ω/Ω/°C -80 to 260
Pt200 (385) 200 Ω Platinum 0.00385 Ω/Ω/°C -200 to 630
Pt500 (385) 500 Ω Platinum 0.00385 Ω/Ω/°C -200 to 630
Pt1000 (385) 1000 Ω Platinum 0.00385 Ω/Ω/°C -200 to 630
Cu10 (427) 9.035 Ω[2] Copper 0.00427 Ω/Ω/°C -100 to 260
Pt100 (3916) 100 Ω Platinum 0.003916 Ω/Ω/°C -200 to 630
[1] Per IEC 751-Standard
[2] 10 Ω @ 25 °C
753/754
Users Manual
40
To measure temperature where an RTD input is used:
1. If necessary, push for MEASURE mode.
2. Push t.
3. Push and then Select RTD Type is shown.
4. Push or to select the necessary RTD type.
5. Push .
6. Push or to select a 2-, 3-, or 4-wire connection.
The connections are shown on the display.
7. Attach the RTD to input jacks as the display or Figure
14 shows. Use the supplied jumper between the mA Ω
RTD MEASURE low jack and the V MEASURE low jack
as shown if using a 3-wire connection.
8. Push .
Caution
To prevent possible damage to the Product, do
not force a dual banana plug between any two
jacks in the horizontal orientation. Doing so
will damage the jacks. Use the supplied jumper
wire when needed for RTD measurements. A
dual banana plug may be used in the vertical
orientation. See Figure 16.
Documenting Process Calibrator
Measure Mode
41
gks14f.eps
Figure 16. Correct Jumper Use
8. If necessary, change between °C, °F, K, and °R
temperature units in Setup:
1. Push s.
2. Push the Next Page softkey twice.
3. Push and to move the cursor to
Temperature Units.
4. Push or the Choices softkey to choose a
setting for that parameter.
5. Push or to move the cursor to the necessary
setting.
6. Push to go back to the s display.
7. Push the Done softkey or s to exit Setup mode.
9. If necessary, change between ITS-90 or IPTS-68
Temperature Scale in Setup mode. The procedure is
the same as steps 1-7 above.
Documenting Process Calibrator
Source Mode
45
Damping Measurements
The Product normally applies a software filter to dampen
measurements in all functions except continuity. The
specifications assume that damping is turned on. The
damping method is a running average of the last eight
measurements. Fluke recommends leaving damping on.
Turning damping off may be useful when measurement
response is more important than accuracy or noise
reduction. To turn damping off, push the More Choices
softkey twice, then push the Dampen softkey so that Off is
shown. Push Dampen again to turn damping back on. The
default state is On.
Note
If a measurement falls outside a random noise window,
a new average is started. If damping is turned off, or
until measurements are fully damped, the symbol is
displayed.
Source Mode
The operating mode (for example, MEASURE, SOURCE) is
shown on the display. If the Product is not in SOURCE
mode, push until SOURCE is shown. The Product
must be in SOURCE mode to change any of the SOURCE
parameters.
Source Electrical Parameters
To select an electrical source function:
1. Connect the test leads as shown in Figure 18,
depending on the source function.
2. Push for current, for dc voltage, h for
frequency, or q for resistance.
3. Record the necessary output value, then push . For
example, to source 5.5 V dc, push 5 . .
753/754
Users Manual
46
Note
If sourcing frequency, respond when the Product
asks you to select a zero-symmetric sine or
positive square wave. The amplitude specified is
p-p amplitude.
4. To change the output value, record a new value and
push .
Note
If sourcing current, wait for the
g
symbol to
disappear before you use the output.
5. To set the output value in the present source function,
push then enter the desired value and push .
6. To turn off sourcing completely, push twice.
Note
Use the source current function to drive a current
loop. This is different than the loop power function
in which the Product is powering a process
instrument. To source loop power, use the Loop
Power function accessible from Setup mode.
Documenting Process Calibrator
Source Mode
47
Common
Common
gks16f.eps
Figure 18. Electrical Source Connections
Documenting Process Calibrator
User-Replaceable Parts
103
Table 12. Replacement Parts
Item Fluke Part Number
Adjustable Quick-Release Strap 3889532
Input/Output Jack Decal 3405856
Tilt Stand 3404790
BP7240 Battery 4022220
USB Cable 1671807
BC7240 Power Supply/Battery Charger 4022655
Lens Cover 3609579
Alligator Clip Set-Extended Tooth 3765923
754HCC HART Communication Cable Assembly 3829410
AC280 Suregrip Hook Clip Set 1610115
TC Cap 4073631
Note: See “Standard Equipment” and “Accessories” for model or part numbers for most replaceable equipment.
115


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke 754 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke 754 in the language / languages: English as an attachment in your email.

The manual is 5,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fluke 754

Fluke 754 User Manual - German - 130 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info