764277
7
Zoom out
Zoom in
Previous page
1/22
Next page
mA Calibrator
Safety Information
3
Never use the Calibrator with the red holster
removed.
Never use the Calibrator with the case open.
Opening the case violates Ex Approval
Make sure the battery door is closed before you
use the Calibrator.
Replace the battery as soon as the M (low
battery) symbol appears to avoid false readings
that can lead to electric shock.
Remove test leads from the Calibrator before
opening the battery door.
This equipment is specified for use in
measurement category I (CAT I) pollution
degree 2 environments and should not be used
in CAT II, CAT III, or CAT IV environments.
Voltage transients should not exceed 300 volts
for the CAT I applications where this product is
used. Measurement transients are defined in
IEC1010-1 as 2 μs rise time with a 50 μs
duration at 50 % of the maximum amplitude
height.
Measurement Category I (CAT I) is defined for
measurements performed on circuits not
directly connected to the mains.
Do not use in a damp or wet environment.
Safety Advice
To ensure safe operation of the Calibrator fully observe all
instructions and warnings contained in this manual. In
case of doubt (due to translation and/or printing errors)
refer to the original English manual.
Faults and Damage
Applying a voltage greater than 28 V to the input of the
Calibrator invalidates its Ex Approval and may impair its
safe operation in an Ex-hazardous area.
If there is any reason to suspect that the safe operation of
the Calibrator has been affected, it must be immediately
withdrawn from use, and precautionary measures must be
taken to prevent any further use of the Calibrator in an Ex-
hazardous area.
The safety features and integrity of the unit may be
compromised by any of the following:
External damage to the housing
Internal damage to the Calibrator
Exposure to excessive loads
Incorrect storage of the unit
Damage sustained in transit
Correct certification is illegible
Using the product with the red holster removed
Functioning errors occur
Permitted limitations are exceeded
Functioning errors or obvious measurement
inaccuracies occur which prevent further measurement
by the Calibrator
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke 707Ex at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke 707Ex in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fluke 707Ex

Fluke 707Ex User Manual - German - 22 pages

Fluke 707Ex User Manual - Dutch - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info