539466
6
Zoom out
Zoom in
Previous page
1/30
Next page
6
GB IE
run the machine at walking pace.
When working, ensure a rm foothold,
particularly on slopes. Always work
across the slope, never up or down-
wards. Take particular care when chang-
ing the direction of travel on the slope.
Do not work on excessively steep slopes.
When switching the machine on, avoid
feet or hands being trapped between
the moving blades and the xed parts
of the machine.
Never carry the machine by the blade
cylinder.
Caution! To avoid damaging the
machine and potential injury as a
consequence:
Check the terrain on which the machine
is used and remove stones, sticks, wires
or other foreign bodies that may be
picked up and ung outwards.
Ensure that the machine is in a safe op-
erating condition. Replace worn or dam-
aged parts.
Protect the machine from the effects of
weathering (damp, frost).
Fitting the Handle
1. Press both ends of the handle bot-
tom (6) together and insert them
vertically through the handle
holder (7) on the machine.
2. Push the holes at the ends over
the two holder bolts (16).
3. Use the screws and wing nuts
from the package to mount the
top part of the handle (1) on the
two cross bars (2).
4. Use the screws and wing nuts
from the package to mount the
cross bars (2) on the bottom part
of the handle (6).
The two centre bars can be secured
in two positions to adjust the handle
bar to your height.
5. Mount the tool holder (5) from
the package to the bottom part of
the handle (6) and snap on the
machine key (3) to it.
Adjusting the Cut Height
The cut height is innitely adjustable from
14–43 mm:
1. Loosen the locknuts (12) on both
sides of the machine.
2. Place one foot on the castors (9)
and set the desired cut height with
both hands on the adjusting han-
dles (14).
Ensure that the machine is set to
the same height on both sides.
3. Retighten the locking screws (12).
Set the cut height no lower than to
where the blade cylinder does not
touch the ground even where it is
uneven.
Working Instructions
Before each use, check the machine
for obvious defects, such as loose,
worn or damaged parts. Check that
all nuts, bolts and screws are sitting
rmly.
Regular mowing stimulates the stronger
formation of leaves in the grass as well as
allowing weeds to die off at the same time.
Thus, the lawn becomes thicker each time it
is mowed and a lawn with even resilience
is produced.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Florabest FHM 38 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FHM 38 A1 in the language / languages: English, Danish, Swedish as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Florabest FHM 38 A1

Florabest FHM 38 A1 User Manual - German, Dutch, French - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info