634650
69
Zoom out
Zoom in
Previous page
1/78
Next page
64
FBK 4 B2
GB
Fitting the hedge trimmer
Start by undoing the screw grip on the boom of the motor unit.
Slide the tab on the front boom of the
hedge trimmer onto the boom
of the
motor unit. Must properly inserted the red
line be flush with the boom of the motor unit.
If this is not possible, pull the starter pull cord to adjust the shaft.
Caution! Switch the on/off switch
to “0”.
Tighten the screw grip
.
NOTE
The assembly of the pole pruner/strimmer/3-section cutting blade/
extension attachment is carried out in the same order.
Removing the hedge trimmer
Undo the screw grip and pull the front boom on the hedge
trimmer out of the boom
on the motor unit.
NOTE
Disassembly of the pole pruner/strimmer/3-section cutting blade/
extension attachment is carried out in the same order.
Swivelling the hedge trimmer
Release the lock/release .
Press the control lever
and swivel the hedge trimmer into the
desired position.
Allow the control lever
to click into the recess in the base plate
(hedge trimmer)
.
Mounting the saw chain and blade
WARNING!
Wear protective gloves! There is a danger of injury from the sharp
cutting teeth.
NOTE
Pay close attention to the running direction of the saw chain
on
the blade
and at the base plate (pole pruner) .
Depending on wear, the blade
can be turned.
Undo the nut
using the open-ended spanner
6^
.
Remove the sprocket cover
.
Lay the saw chain
over the blade starting at the tip.
Now fit the blade
and saw chain .
Lay the guide rail
over the blade guide while inserting the chain
tensioner pin
in the blade hole . At the same time, lay the saw
chain
over the chain sprocket .
Now you can tighten the saw chain
(see section "Tightening and
checking the saw chain").
Replace the sprocket cover
and tighten the nut gently.
Removing the saw chain
You may have to loosen the saw chain to remove the blade
and the saw chain
(see section "Tightening and checking the saw
chain"). Follow these instructions in reverse order.
Tightening and checking the saw chain
WARNING!
Wear protective gloves! There is a danger of injury from the sharp
cutting teeth.
Turn the chain-tensioner screw
in a clockwise direction using the
flat-blade screwdriver
6&
to increase the tension.
The saw chain
must lie against the underside of the blade. Check
whether the saw chain
can be drawn by hand over the blade .
NOTE
A new saw chain
stretches and must be tightened more regularly.
Lubricating the chain
Remove the oil filler cap .
Fill the oil tank
with approx. 100ml of organic chain oil
6!
.
The chain lubrication can be increased or decreased using the oil
adjusting screw
.
Press and then turn the oil adjusting screw
clockwise to decrease
the chain lubrication.
Press and then turn the oil adjusting screw
anticlockwise to increase
the chain lubrication.
WARNING!
Never work without chain lubrication!
If the saw chain runs dry, the cutting equipment may become irrepar-
ably damaged in a short time. Always check chain lubrication and
oil level in the tank before starting work.
NOTE
Use only saw chain oil. Preferably biodegradable. Do not use waste
oil, motor oil, etc.
While working, check whether the chain lubrication is working correctly.
Sharpening the saw chain
NOTE
A grinder can be attached to the grinder support
for a secure grip
during grinding.
You will find detailed information on sharpening in the sharpening
set, e.g. from Oregon.
Alternatively, you can use an electrical saw chain sharpening device
and follow the manufacturer's instructions .
If you have any doubts about carrying out the work, the saw chain
should be replaced.
Attaching the extension attachment
CAUTION!
Do not use the extension attachment/boom
5$
in combination with
the 3-section cutting blade/strimmer attachment!
NOTE
Use the extension attachment/boom
5$
for working at greater
heights.
Fit the extension attachment/boom
5$
between the motor unit and the
hedge trimmer/pole pruner. The assembly is carried out in the same
manner as for the attachments described previously.
69


Need help? Post your question in this forum.

Forumrules
1

Forum

florabest-fbk-4-b2---4-in-1--ian-273489

Reset search

  • Bonjour,
    J'ai une débroussailleuse Parkside FBK 4 B2-1 dont le bouton du starter est cassé. Je cherche donc un filtre à air compatible. Je cherche aussi une nouvelle tête pour le roto-fil.
    Pouvez-vous me donner les prix et délai. Merci
    Cordialement Submitted on 19-8-2022 at 11:21

    Reply Report abuse
  • Looking we’re to buy new choke lever for florabest FBK 4 B2 Submitted on 25-11-2021 at 15:07

    Reply Report abuse
  • Bonjour je recherche un arbre de transmission florabest ref fkb4 b2 Submitted on 14-7-2021 at 20:52

    Reply Report abuse
  • BONJOUR JE CHERCHE LES EMBOUT POUR LES RALONGES ET OUTILS 4 EN 1 DE LA DEBROUSAILLEUSE FLORABEST FBK 4 B2-1
    NUMERO DES MANCHON 5010259201 Submitted on 19-5-2020 at 11:45

    Reply Report abuse
  • I need a recoil starter unit and pawl for FBS 25 A1 / IAN 280454 multi tool can anyone tell me where I can get them from Submitted on 18-5-2020 at 17:31

    Reply Report abuse
  • New choke leaver for florabest multi strimmer fbk-ebb -1 s/n081439 Submitted on 30-3-2020 at 16:09

    Reply Report abuse
  • Engine is turning first through first section but will not drive any of the attachments
    Maynard Submitted on 12-7-2019 at 00:42

    Reply Report abuse
  • Machine has worked fine for 2 years. Now will not start. Have changed fuel that was in the tank, changed spark plug, cleaned air filter, still no joy. Doesn't even sound as if it wants to start. Any ideas or suggestions ?
    Desperate Den. Submitted on 26-2-2019 at 16:16

    Reply Report abuse
    • The part that produces the spark when you pull the cord went faulty with mine,and required replacement. Unfortunately I cannot remember what it is called. Hope this helps. Answered on 28-2-2019 at 16:55

      Vote up Report abuse
    • Thanks for your input, gives me a new avenue to explore. Answered on 28-2-2019 at 21:11

      Vote up Report abuse
    • You could check if the plastic pipe into the tank has broken and dropped off inside. This will not be obvious when you open the lid because part of it will still be attached to the engine. Answered on 10-10-2020 at 15:14

      Vote up (1) Report abuse
  • Fuel doesn't appear to be supplying the engine. When the unit is on its side it idles but when I put it upright it cuts out. Submitted on 27-5-2017 at 14:11

    Reply Report abuse
    • I had that problem and it was the small tube coming from the fuel tank that was split just inside the tank. Answered on 8-5-2020 at 10:40

      Vote up Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Florabest FBK 4 B2 - 4 in 1 IAN 273489 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FBK 4 B2 - 4 in 1 IAN 273489 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 3,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Florabest FBK 4 B2 - 4 in 1 IAN 273489

Florabest FBK 4 B2 - 4 in 1 IAN 273489 User Manual - Dutch, Danish - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info