505181

Flex LDC 1509 FR 120 Manual

15
Zoom out
Zoom in
Previous page
1/230
Next page
LDC 1709 FR/LD 1709 FR/LDC 1509 FR
15
Safety instructions
t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåëK=
c~áäìêÉ=íç=çÄë Éêî É=íÜÉ=ë~ ÑÉíó =
áåëíêìÅíáçåë=~åÇ=çíÜÉê =áåëíêìÅíáç åë=ã~ó=êÉëìäí=
áå ~å=ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ =~ å ÇLçê =ëÉêáçìë= áåàìêáÉë
K=
hÉÉé=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåë=áå=~=ë~ÑÉ=éä~ÅÉ=Ñçê=íÜÉ=ÑìíìêÉK
This power tool is intended to function
as a grinder. Read all safety warnings,
instructions, illustrations and specifica-
tions provided with this power tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious
injury.
Operations as sanding, wire brushing,
polishing or abrasive cutting-off
operations are not recommended to
be performed with this power tool.
Operations for which the power tool was not
designed may create a hazard and cause
personal injury.
Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer.
Just because the accessory can be attached
to your power tool, it does not assure safe
operation.
The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool.
Accessories running faster than their rated
speed can break and fly apart.
The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be
adequately guarded or controlled.
The arbour size of wheels, flanges,
backing pads or any other accessory
must properly fit the spindle of the power
tool.
Accessories with arbour holes that do not
match the mounting hardware of the power
tool will run out of balance, vibrate excessively
and may cause loss of control.
Do not use a damaged accessory.
Before each use inspect the accessory
such as abrasive wheels for chips and
cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or
cracked wires. If power tool or accessory
is dropped, inspect for damage or install
an undamaged accessory. After inspec-
ting and installing an accessory, position
yourself and bystanders away from the
plane of the rotating accessory and run
the power tool at maximum no-load
speed for one minute.
Damaged accessories will normally break
apart during this test time.
Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and shop apron
capable of stopping small abrasive
or workpiece fragments.
The eye protection must be capable of
stopping flying debris generated by various
operations. The dust mask or respirator must
be capable of filtrating particles generated by
your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
Keep bystanders a safe distance away
from work area. Anyone entering the work
area must wear personal protective
equipment.
Fragments of workpiece or of a broken
accessory may fly away and cause injury
beyond immediate area of operation.
Hold power tool by insulated gripping
surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring or its own
cord.
Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool
“live” and shock the operator.
Position the cord clear of the spinning
accessory.
If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled
into the spinning accessory.
Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the surface
and pull the power tool out of your control.
Do not run the power tool while carrying
it at your side.
Accidental contact with the spinning
accessory could snag your clothing,
pulling the accessory into your body.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Flex LDC 1509 FR 120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Flex LDC 1509 FR 120 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info