604747

Fisher Paykel AquaSmart 2 Manual

6
Zoom out
Zoom in
Previous page
1/48
Next page
4
Installation instructions
Water supply
This clothes washer should be plumbed into both a hot and cold water supply otherwise some
cycles may not function correctly.
Your hot water should not exceed 65˚C, and your cold water should not exceed 35˚C.
Temperatures above these may cause a fault or cause damage to the machine.
If you have an uncontrolled water-heating source (eg a wet back or solar heating) you should
have a tempering device fitted. This will ensure the hot water temperature remains within
safe limits. For the most suitable type of tempering device we recommend you contact a local
plumber or plumbing supply merchant.
Inlet Water Static Pressure of between 3 psi (20 kPa) and 150 psi (1 MPa) is required.
(If using a header tank then the top of the header tank must be at least 2 metres above the top
of your clothes washer).
Minimum flow rate from the tap supplying the clothes washer should be greater than
6 litres/min (assumes 12.7 mm (⁄ inch) diameter pipes).
Minimum height of taps to clear the top of the machine is 1150 mm.
Inlet hoses
Note:
New hose sets provided with the washer shall be used to
connect the washer to the water mains.
Old hose sets should not be re-used.
1
Connect the straight ends of the inlet hoses to the taps
(there are washers fitted in both ends). Connect the red
connector hose to hot, and white connector hose to cold
(if your hoses are colour-coded).
2
Connect the elbow ends of the inlet hoses to the machine
inlet valves. Inlet valves are marked on the back of the
machine. Ensure the hot valve is connected to the hot tap
and the cold valve is connected to the cold tap.
H = Hot C = Cold
Inlet hose replacement
We recommend replacing the inlet hoses every 5 years. Hoses should be checked from time to
time and replaced if any wear, cuts, bulges, kinks or leaks are found.
Electrical
This appliance must be supplied with a 230 V – 240 V, 50 Hz, sinusoidal, 450 W electrical supply.
Tap end
Machine end
Fig.4 Inlet hose ends
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fisher Paykel AquaSmart 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fisher Paykel AquaSmart 2 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info