795154
24
Zoom out
Zoom in
Previous page
1/99
Next page
Page 24
PTZ CONTROLS
Configuring PTZ Settings
PTZ is an acronym for pan, tilt, zoom. PTZ cameras that allow
the camera to pan left and right, tilt up and down, and zoom
in and out. To set the parameters of a PTZ camera, enter the
PTZ Settings interface: Menu > Camera > PTZ.
1. Choose camera from Camera dropdown list.
2. Choose the camera for PTZ setting in the Camera
dropdown list.
3. Click the RS-485 Settings button to set the RS-485
parameters.
All the parameters should be exactly the
same as the PTZ camera parameters
4. Click Apply.
NOTE:
Customizing Presets
Set a preset location for a PTZ camera to point to when an
event takes place: Menu > Camera > PTZ
1. Use the directional button to wheel the camera to the
location where you want to set preset; and the zoom and
focus operations can be recorded in the preset as well.
2. Enter the preset No. (1~255) in the preset text field, and
click the Set button to link the location to the preset.
Repeat the steps 1-2 to save more presets.
Click the Clear button to clear the location information of
the preset, or click the Clear All button to clear the location
information of all the presets.
Setting PTZ Presets, Patrols, and Patterns
Before you start
Make sure that the presets, patrols and patterns
should be supported by PTZ protocols.
PTZ
Pan/Tilt/Zoom (PTZ) Setup:
NOTE: Consult the instruction manual of your PTZ camera for complete
information about your camera, including protocol, baud rate and parity
settings before beginning setup. Enter these settings in the DVR.
Connect your PTZ Camera to this DVR
Connect a PTZ camera to the BNC and DC power cables. Also, connect the
communication cable from the PTZ camera to the 485A (TX, +) and 485B
(RX, -) control inputs to the PTZ block on the back of the DVR. Note there
is only one set of PTZ control inputs (485A & 485B), however multiple PTZ
cameras can be set up by making parallel connections. See diagram for
details and see “PTZ Camera Setup” Info box for additional information.
Install 120 Ω
terminating
resistor in last
camera only
AB AB AB
~
~
PTZ Inputs Configuration
RS485
+ +
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for First Alert DVRAHD-0810 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of First Alert DVRAHD-0810 in the language / languages: English as an attachment in your email.

The manual is 7.11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info