795094

First Alert 3040DFE Manual

4
Zoom out
Zoom in
Previous page
1/4
Next page
3
English
Getting Started
4
English
Programming your
Personal Passcode
STEP 4: Opening your Security
Box using the pre-set factory
code
THE PRE-SET FACTORY CODE IS 3*
Using the keypad, enter the factory pre-set
code. The LED will flash a green light and
stay green for 10 seconds after the
button is pressed. You will hear the
Security Box unlock.
NOTE: You have 10 seconds to open the
Security Box. If the green light goes out,
you will have to re-enter the code.
To open, turn the knob from the locked
position to the unlocked position, one
quarter turn counter-clockwise. To open, lift
from the outer edge of the lid. (fig.2)
If the LED light flashes red after you enter
the code, this means the code was entered
incorrectly and the Security Box will not
open.
NOTE: If an incorrect code is entered 3
times in a row, the Security Box will
automatically shut down for 4 minutes
before it can be opened again using the
correct code. During this delay, the
Override Key can be used to open the
Security Box.
NOTE: For your security, immediately
re-program the digital lock to your
Personal Passcode.
Open your Security Box with the Override
Key or with the pre-set factory Passcode.
On the inside of the lid, find and press
the red button located to the side of the
battery compartment (Fig.3). The LED light
above the keypad will flash orange.
Enter your personal Passcode, up to 5
digits, followed by the button and then
repeat a second time. You must enter
the number twice.
For example: 1 2 3 4 5 - 1 2 3 4 5
After the first entry, the LED will flash orange.
After the second entry, the LED will flash
green and then go out.
Your Personal Passcode is now saved.
Write it down and store it in a secure place
away from the Security Box.
Close the lid of your Security Box and
return the knob to the locked position (Fig. 6).
If the override key was used, turn to the
locked position, remove and replace the
lock cover.
NOTE: The factory pre-set code is no longer active and cannot
be used to open the Security Box.
STEP 1: Locate Override Keys
Keys and batteries are stored in the packing
material. Remove them before discarding
the box.
STEP 2: Opening your Security
Box using your Override Key
Remove cover from key lock.
Insert Override Key into key lock and turn
the key counter clockwise one quarter turn
to the unlocked position.
Turn the knob counter-clockwise one
quarter turn to the unlocked position. (fig.1)
To open, lift from the outer edge of the lid.
(fig.2)
STEP 3: Installing Batteries
Locate the battery cover on the back side
of the lid. (fig.4)
Slide the cover off the battery
compartment.
Properly insert batteries, noting correct
direction, replace cover and close the
Security Box lid.
Return the Override Key and the knob to
the locked position.
NOTE: Clean the battery contacts in the battery
compartment and on the batteries before
installing new batteries.
Closing and Securing your
Security Box
Be careful not to overfill your Security Box
or obstruct the door from completely
closing.
Make sure knob is in the unlocked position.
Make sure lid is closed completely. (Fig. 5)
Turn the knob from the unlocked position
one quarter turn clockwise to the locked
position. Your Security Box should now be
secured.
NOTE: While the override key is in the
unlocked position you can open and close
the Security Box by turning the knob from
the locked to the unlocked position and
back again without entering your personal
code. To secure your Security Box, make
sure that you have turned the override key
to the locked position and have stored the
key away from the Security Box in a safe
place.
Troubleshooting
No light from LED: This indicates that the
batteries are expired and need to be
replaced. To change the batteries, see
Getting Started STEPS 2 & 3.
NOTE: Replacing batteries does not
erase your personal code.
The LED is blinking a red light:
This means that your batteries are low. To
change your batteries, see Getting Started
STEPS 2 & 3.
Warning: DO NOT FORCE THE KNOB
If forced, the knob will break and your
Security Box will be damaged. When
operated correctly, the knob will function
so that it can be turned easily into the
opened position.
If you have additional questions while
operating your Security Box, please
contact BRK Brands Europe Ltd.
Security Cable
Remove the plug from
security cable
attachment hole.
Loop cable around
desired object and then
through itself.
Depress cable release
button and while holding
down, insert security
cable into the hole as
shown in diagram, then
release button.
Model 3040DFE
includes security cable.
1
2
3
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for First Alert 3040DFE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of First Alert 3040DFE in the language / languages: English as an attachment in your email.

The manual is 1.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info