795166

First Alert 1039102 - Onelink Manual

17
Zoom out
Zoom in
Previous page
1/32
Next page
17
Regular Maintenance
Alarm End of Life
This unit has been designed to be as maintenance-free as possible, but there are
a few simple things you must do to keep it working properly:
• Test it at least once a week.
• Clean the smoke/CO alarm at least once a month; gently vacuum the outside of the smoke/CO
alarm using your household vacuum’s soft brush attachment. A can of clean compressed air (sold at
computer or oce supply stores) may also be used. Follow manufacturer instructions for use. Test
the smoke/CO alarm. Never use water, cleaners or solvents since they may damage the unit.
• After cleaning test the alarm.
• If the smoke/CO alarm becomes contaminated by excessive dirt, dust and/or grime, and
cannot be cleaned to avoid unwanted alarms, replace the unit immediately.
• Relocate the unit if it sounds frequent unwanted alarms. See “Where Not To Install” for details.
Discharging the Alarm
After 10 years of operation or low battery warning, discharge the alarm by following the diagram below:
Puncture label in the dotted circle with a screwdriver and slide switch all the way to the left to DISCHARGE.
NOTE: At end of life or low battery indication (chirp): unit must be put into discharge mode
to discharge remaining stored energy in battery. Unit will no longer function once put into this
mode. Unit will resist re-mounting. Once discharged, replace alarm immediately.
!
IM P ORTANT: Actual battery service life depends on the smoke/CO alarm and the
environment in which it is installed. Regardless of the manufacturer’s suggested battery life, you
MUST replace the alarm immediately once the unit starts “chirping” (the “low battery warning”).
1. Puncture label on dotted circle
2. Slide switch to the left
DISCHARGE
Puncture circle
with tool, slide to
permanently
discharge.
PHOTOELECTRIC
W
IMPORTANT!
CARBON MONOXIDE SENSITIVITY:
If CO levels reach 70ppm,
it must activate within 60-240 minutes. At 150ppm within
10-50 minutes. At 400ppm within 4-15 minutes.
Refer to user’s manual for more information.
Installed On
Replace By
Replace alarm 10 years after installation.
CONFORMS TO
UL STD 217 & UL STD 2034
3055574
Follow and Retain User’s Manual: BRK
Brands, Inc.
1301 Joe Battle, El Paso, TX 79936.
Customer Service Team: 1(833) ONE-LINK
www.rstalert.com (1-833-663-5465)
BLACK
•
LINE
ORANGE
•
INTERCONNECT
WHITE
•
NEUTRAL
W
WARNING!
Carbon monoxide cannot be seen or smelled but can kill
you. If alarm signal sounds: 1. Operate Test/Silence button.
2. Call your emergency services. (Fire Dept. or 911)
3. Immediately move to fresh air - outdoors or by an open door/window.
HOW TO DISCHARGE ALARM:
Puncture circle with tool and slide as indicated to
permanently discharge battery. Once discharged, the alarm
cannot be reactivated and must be replaced.
MAINTENANCE AND TESTING:
Alarm is sealed, with no serviceable parts. Battery is not
replaceable. Constant use at high or low temperatures or
high humidity may reduce battery life. Test after installation,
weekly, and after cleaning. Clean monthly – gently vacuum
or use clean compressed air to remove dust. Never use
water, cleaner or solvent, since this may damage the unit.
ALARM GUIDE:
SMOKE ALARM: Three beeps. Three red ashes.
CO ALARM: Four beeps. Four red ashes.
MALFUNCTION: Three “chirps” per minute. Three yellow ashes. Replace alarm.
END OF LIFE: Five “chirps” per minute. Five yellow ashes. Replace alarm.
LED light indicates AC power
SINGLE AND/OR MULTIPLE STATION
SMOKE & CO ALARM
MODEL NO. 1039102
120V AC 134 mA 3.0 Lithium Battery Backup
SMOKE SENSITIVITY: 1.15%-3.20% ft OBSC.
HOW TO ACTIVATE ALARM:
NOTE: Ensure the AC Plug is connected rst prior to
mounting the unit to activate battery back-up.
Install the mounting bracket, align the base of the
alarm to the mounting bracket and turn clockwise.
Contains Transmitter Modules FCC ID:2ANOG-A76F
DISCHARGE
Puncture circle
with tool, slide to
permanently
discharge.
PHOTOELECTRIC
W
IMPORTANT!
CARBON MONOXIDE SENSITIVITY:
If CO levels reach 70ppm,
it must activate within 60-240 minutes. At 150ppm within
10-50 minutes. At 400ppm within 4-15 minutes.
Refer to user’s manual for more information.
Installed On
Replace By
Replace alarm 10 years after installation.
CONFORMS TO
UL STD 217 & UL STD 2034
3055574
Follow and Retain User’s Manual: BRK
Brands, Inc.
1301 Joe Battle, El Paso, TX 79936.
Customer Service Team: 1(833) ONE-LINK
www.rstalert.com (1-833-663-5465)
BLACK
•
LINE
ORANGE
•
INTERCONNECT
WHITE
•
NEUTRAL
W
WARNING!
Carbon monoxide cannot be seen or smelled but can kill
you. If alarm signal sounds: 1. Operate Test/Silence button.
2. Call your emergency services. (Fire Dept. or 911)
3. Immediately move to fresh air - outdoors or by an open door/window.
HOW TO DISCHARGE ALARM:
Puncture circle with tool and slide as indicated to
permanently discharge battery. Once discharged, the alarm
cannot be reactivated and must be replaced.
MAINTENANCE AND TESTING:
Alarm is sealed, with no serviceable parts. Battery is not
replaceable. Constant use at high or low temperatures or
high humidity may reduce battery life. Test after installation,
weekly, and after cleaning. Clean monthly – gently vacuum
or use clean compressed air to remove dust. Never use
water, cleaner or solvent, since this may damage the unit.
ALARM GUIDE:
SMOKE ALARM: Three beeps. Three red ashes.
CO ALARM: Four beeps. Four red ashes.
MALFUNCTION: Three “chirps” per minute. Three yellow ashes. Replace alarm.
END OF LIFE: Five “chirps” per minute. Five yellow ashes. Replace alarm.
LED light indicates AC power
SINGLE AND/OR MULTIPLE STATION
SMOKE & CO ALARM
MODEL NO. 1039102
120V AC 134 mA 3.0 Lithium Battery Backup
SMOKE SENSITIVITY: 1.15%-3.20% ft OBSC.
HOW TO ACTIVATE ALARM:
NOTE: Ensure the AC Plug is connected rst prior to
mounting the unit to activate battery back-up.
Install the mounting bracket, align the base of the
alarm to the mounting bracket and turn clockwise.
Contains Transmitter Modules FCC ID:2ANOG-A76F
2
1
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for First Alert 1039102 - Onelink at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of First Alert 1039102 - Onelink in the language / languages: English as an attachment in your email.

The manual is 2.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info