You can set a DRINK FIT function during the setting of your personal datas. You can choose between OFF, 15, 20, 25
and 30minutes. The symbol will be shown for 3 seconds with an beep in the matrix, it doesn´t matter in which program
you are.
%XPLANATIONOFTHESYMBOLSANDNEEDTOKNOW
The symbol demand you to begin to pedal. the set values will be confirmed and you start your exercise.
!0EDALLING
"$RINK&)4
$3ETTINGVALUES
Target values: After achieving the target values, there will be a beep and the computer will stop counting. The monitor will show the average
and trip values. To continue your exercise, you have to reactivate the computer by pressing the DELETE button.
!TTENTION Except the heartrate value, you can set only one further value. If you set another value, the already set value will be set to OFF.
To start your exercise, beginn to pedal, after you have set the target value.
%()7ATT
In PROGRAM-Mode, you can set the max Watt resistance which will be reached during your exercise. All other Watt values will be calculatated
accordingly to the max value.
&2ECOVERY
After you finished your exercise press RECOVERY and stop pedalling. The computer will measure the heartrate for the next 60 seconds. If the
difference between the starting and end heartrate is around 20%, you will get the grade F1 (very good).
#7AKINGUPTHECOMPUTERFROMTHESNOOZEMODE
To reactivate the computer from the snooze mode, press any button, please. A pedalling has no function in this mode.
')NCREASINGOFTHE7ATTVALUEDURING(2#-ODE
The resistance (watt value) will be increase every 30 seconds for 10 Watt, till you reach a heart rate value, which is 5 beats lower than your
target. The resistance will stay at this level for 1 minute. If there is no further heartrate change, the resistance will increase again. If the actual
heartrate is for 5 seconds higher than your target, the resistance will decrease immediately for 20 Watt and than every 20 seconds for 10 Watt,
till your actual heartrate is lower than the target. If it is lower than the target heartrate, the resistance will increase again.
For IND: You can set a heartrate zone. The increasing is following the same procedure like above mentioned. Pay attention, that if your actual
heartrate cannot be under the LO limit, the resistance will not increase anymore. You have to stop your exercise and set new targets!
The arrows in the heartrate windows indicate, that the resistance cannot be increased or decreased and so you have to pedal slower (arrow
down) or pedal faster (arrow up).
If your actual heartrate is five beats lower than the set target, the circle between the two arrows start to blink. It indicates, that you are reaching
your target value. If your actual heartrate is higher than the high limit, there will be a beep and the actual heartrate starts blinking.
&!'%
Needed for max heartrate calculation.
'+CALCALCULATION
Shows the energy consumption, based on a efficiency of 22% to provide the mechanical power. Conversion Joule into Kcal: 1cal=4,1867J.
Example: 60Watt for 20minutes
60(Watt) x 20(Min) x 60Rpm=72000J= 17197cal.
17197cal is equal to a efficieny of 22%. Totally the calorie consumption is 78169cal oder 78Kcal.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Finnlo 3279 Loxon XTR at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Finnlo 3279 Loxon XTR in the language / languages: English, German as an attachment in your email.
The manual is 2,61 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
