528535
25
Zoom out
Zoom in
Previous page
1/36
Next page
Fehler
Keine Anzeige oder keine Funktion des Computers
Ursache
Keine Stromversorgung
Fehler
Pulsanzeige fehlerhaft
Ursache
Kein Empfang
Störquellen im Raum
Bei Handpuls:
Nicht beide Hände an
beiden Sensoren
Keine Pulswerterfassung
Bei Ohrpulsmessung:
Schlechte Durchblutung des
Ohrläppchens
Keine Pulswerterfassung
Bei Brustgurt:
ungeeigneter Brustgurt
Brustgurt falsch positioniert
Batterien sind leer
Fehler
Tretwiderstand nicht regelbar
Ursache
Mechanik / Steuerung
Fehler
Anzeige zu schwach
Ursache
Ungünstiger Lichteinfall
Fehler
Fehlende Teile
Fehler
Wackelndes Gerät
Ursache
Unebener Boden
Standfüße locker
Was tun?
Netzgerät in Steckdose
einstecken.
Netzgerätestecker in An-
schlussbuchse am Gehäuse
einstecken Kabelverbindungen
überprüfen
Was tun?
Alle Anschlüsse überprüfen
Evtl. Störgrößen (z.B. Handy/
Lautsprecher) im Raum
beseitigen
Beide Handächen gleichzeitig
auf beide Sensoren auegen!
Korrekten Sitz der Hand-
pulskabel in den zugehörigen
Anschlussbuchsen auf der
Rückseite des Computers
überprüfen!
Ohrläppchen massieren
Korrekten Sitz des Ohrclips
prüfen und das Kabel an der
Kleidung befestigen.
Evtl. anderen Brustgurt ver-
wenden. Die Sendefrequenz
muss zw. 5,0 – 5,5 kHz
liegen!
Elektroden befeuchten und
korrekten Sitz überprüfen.
Durch Batterien desselben
Typs ersetzen
Was tun?
Programm mit Quick-Start
starten Kabelverbindungen
prüfen
Was tun?
Stellung des Gerätes ändern
Was tun?
Verpackung überprüfen
Service anrufen
5.4 Fehlerdiagnose und Fehlersuche
24
Was tun?
Höhenverstellkappen drehen,
bis ein sicherer Stand
gewährleistet ist!
Hutmuttern festziehen!
5.4 Diagnostics and Troubleshooting
Error
No display or computer is not functioning
Cause
No power
Error
Pulse display defective
Cause
No reception
Interference with in the room
Hand pulse Grip:
Both hands not on both sensors
No pulse rate acquisition
Earpulse measurement:
Poor blood circulation
No pulse rate acquisition
Chest Strap:
Incorrect chest strap
Chestbelt strap incorrectly
positioned
Batteries are dead
Error
Step resistance cannot be regulated.
Cause
Mechanics/control system
Error
Computer display to weak
Cause
Detrimental light fall
Error
Missing parts
Error
Wobbly equipment
Cause
Uneven oor
Stand feet are loose
What to do?
Plug the power supply into
the socket, or plug the power
supply into the connection
port on the housing (see
Assembly Step 9), or Check
cable connections
What to do?
Check all connections
Remove (for example cell
phone/loud speakers)
in the room
Place both hand surfaces on
both sensors at the same
time.
Check for correct seating
of the pulse grip cable in
the appropriate connection
jacks on the rear panel of the
computer.
Massage for your earlobe.
Check for correct seating of
the pulse grip cable and x it
on your textile
Use another chest strap, if
necessary. The transmitting
frequency must be between
5.0 -5.5 kHz.
Moisten the electrodes and
check for correct positioning.
Replace the batteries with
ones of the same type.
What to do?
Start the program using
Quick Start. Check cable
connections
What to do?
Change the position of the
equipment
What to do?
Check the packing or
Call Service
What to do?
Rotate the height adjusting
caps until the stand is stable.
Tighten the cap nuts.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Finnlo 3253 LOXON XT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Finnlo 3253 LOXON XT in the language / languages: English, German as an attachment in your email.

The manual is 4,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info