500524
13
Zoom out
Zoom in
Previous page
1/42
Next page
English - 12 -
Using Side AV Connectors
You can connect a range of optional equipment to your
LED TV using side connectors of the TV.
For connecting a camcorder or camera , you should
use AV socket (side). To do this, you must use the
supplied audio/video connection cable. First, plug
single jack of the cable to the TV’s AV IN socket
(side). Afterwards, insert your camera cable’s
(not supplied) connectors into the plural part of
the audio/video connection cable. Colours of the
connected jacks should match (YELLOW for VIDEO
connection, WHITE/RED for audio connection). See
illustration below.
Camera
AV Connection
Cable (supplied)
AV Cable
(Not supplied)
Headphone
Afterwards, you should switch to Side AV source.
See the section Input selection in the following
sections for more information.
To listen the TV sound from headphones, you
should connect headphones to your TV by using the
HEADPHONE jack as illustrated above.
Using Other Connectors
You can connect a range of optional equipment to your
TV. A possible connection is shown below. Note that
cables shown in the illustration are not supplied.
For connecting to a device that has SPDIF support,
use an appropriate SPDIF cable to enable sound
connection.
A device that
supports
SPDIF signal.
Remote Control Handset
Inserting Batteries
Remove the battery cover located on the back of
the handset by gently pulling backwards from the
indicated part.
Insert two AAA/R3 or equivalent type batteries
inside. Observe the correct polarity (+/-) when
inserting batteries and replace the battery cover.
Note: Remove the batteries from the remote control
handset when it will not be used for a long period.
Otherwise it can be damaged due to any leakage of
batteries. Remote range is approximately 7m/23ft.
Switching On/Off
To Switch the TV On
Connect the power cord to the 220-240V AC, 50 Hz.
Press STANDBY touch button. Then the standby
LED lights up.
To switch the TV on from standby mode either:
Press the “
” button, P+ / P- or a numeric button on
the remote control.
Press the -P/CH or P/CH+ touch button on the TV. The
TV will then switch on.
Note: If you switch on your TV via PROGRAMME UP/
DOWN buttons on the remote control or on the TV
set, the programme that you were watching last will be
reselected.
To Switch the TV Off
Press the “ ” button on the remote control or press
the “
” touch button on the TV, so the TV will switch
to standby mode.
To power down the TV completely, unplug the
power cord from the mains socket.
Note: When the TV is switched to standby mode,
standby LED can blink to indicate that features such as
Standby Search, Over Air Download or Timer is active.
The LED can also blink when you switch on the TV from
standby mode.
01_MB69_[GB]_DVB-T_5103UK_42912LED_GOLD17_10076864_50208406.indd 1201_MB69_[GB]_DVB-T_5103UK_42912LED_GOLD17_10076864_50208406.indd 12 26.12.2011 14:28:1226.12.2011 14:28:12
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Finlux 42F7010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Finlux 42F7010 in the language / languages: English as an attachment in your email.

The manual is 4,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info